The RFC Archive
 The RFC Archive   RFC 1954   « Jump to any RFC number directly 
 RFC Home
Full RFC Index
Recent RFCs
RFC Standards
Best Current Practice
RFC Errata
1 April RFC



IETF RFC 1954

Transmission of Flow Labelled IPv4 on ATM Data Links Ipsilon Version 1.0

Last modified on Tuesday, May 21st, 1996

Permanent link to RFC 1954
Search GitHub Wiki for RFC 1954
Show other RFCs mentioning RFC 1954







Network Working Group                                 P. Newman, Ipsilon
Request for Comments: 1954                         W. L. Edwards, Sprint
Category: Informational                             R. Hinden, Ipsilon
                                                     E. Hoffman, Ipsilon
                                                  F. Ching Liaw, Ipsilon
                                                        T. Lyon, Ipsilon
                                                    G. Minshall, Ipsilon
                                                                May 1996


          Transmission of Flow Labelled IPv4 on ATM Data Links
                          Ipsilon Version 1.0

 Status of this Memo

   This document provides information for the Internet community.  This
   memo does not specify an Internet standard of any kind.  Distribution
   of this memo is unlimited.

 IESG Note:

   This note documents a private protocol for IPv4-based flows.  This
   protocol is NOT the product of an IETF working group nor is it a
   standards track document. It has not necessarily benefited from the
   widespread and in depth community review that standards track
   documents receive.

 Abstract

   This document specifies the manner for transmitting IPv4 datagrams
   over an ATM data link, both in a default manner and in the presence
   of flow labelling via Ipsilon Flow Management Protocol [IFMP].

 Table of Contents

   Introduction....................................................2
   1. Labels.......................................................2
   2. Default Encapsulation........................................2
   3. Flow Type 0 Encapsulation....................................3
   4. Flow Type 1 Encapsulation....................................4
   5. Flow Type 2 Encapsulation....................................5
   References......................................................7
   Security Considerations.........................................7
   Authors' Addresses..............................................7







Newman, et. al.              Informational                   PAGE 1 top


RFC 1954 Flow Labelled IPv4 on ATM May 1996 Introduction This document specifies the manner for transmitting IPv4 datagrams over an ATM data link, both in a default manner and in the presence of flow labelling via Ipsilon Flow Management Protocol [IFMP]. ATM specific functions such as OAM cells, the CLP bit, and ABR RM cells are not used. There are no reserved VCIs other than VPI = 0, VCI = 0, which indicates an unassigned cell; and VPI = 0, VCI = 15, which is used for the default encapsulation. IFMP messages must be sent using the default encapsulation. 1. Labels Labels, as carried by IFMP, are realized on an ATM data link as specific VPI/VCIs. The format of the Label field for ATM labels is: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Reservd| VPI | VCI | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The low order 16 bits of the label correspond to the VCI, with the least significant bit of the Label field corresponding to the least significant bit of the VCI. If the link cannot support a full 16 bit VCI the unused bits of the VCI must be the most significant bits and they must be set to zero. The next 12 higher order bits of the label correspond to the VPI, with the least significant of these bits corresponding to the least significant bit of the VPI. If the link cannot support a full 12 bit VPI, then the unused bits of the VPI must be the most significant bits and they must be set to zero. The most significant four bits of the label are reserved. They should be set to zero by the sender and ignored by the receiver. 2. Default Encapsulation The default encapsulation for IPv4 packets on ATM data links is the LLC/SNAP encapsulation specified in section 4.1 "LLC encapsulation for routed protocols" of RFC 1483 [RFC 1483]. Such frames begin with the octets 0xAA 0xAA 0x03 0x00 0x00 0x00 0x08 0x00 (the LLC/SNAP header for IPv4). The LLC/SNAP header is prefixed to the IP datagram and the entire packet is encapsulated within the payload of an AAL-5 CPCS-PDU as specified in RFC 1483 and illustrated below: Newman, et. al. Informational PAGE 2 top

RFC 1954 Flow Labelled IPv4 on ATM May 1996 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LLC (0xAA-AA-03) | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | SNAP (0x00-00-00-08-00) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | ~ IPv4 Datagram ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Pad (0 - 47 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + AAL-5 CPCS-PDU Trailer (8 octets) + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The maximum transmission unit (MTU) of an IPv4 datagram using the default encapsulation is 1500 octets. Frames using the default encapsulation are sent to: VPI = 0, VCI = 15. 3. Flow Type 0 Encapsulation All IPv4 frames using Flow Type 0 are encapsulated within the payload of an AAL-5 CPCS-PDU. This is the null encapsulation of section 5.1 "VC based multiplexing of routed protocols" from RFC 1483 [RFC 1483]. There is no LLC/SNAP header. The first octet of the frame corresponds to the first octet of the IPv4 datagram (i.e., the octet that contains the IP version number (4) and Internet Header Length (IHL) ). The IP datagram is encapsulated within the payload of an AAL-5 CPCS-PDU as specified in RFC 1483 and illustrated below: Newman, et. al. Informational PAGE 3 top

RFC 1954 Flow Labelled IPv4 on ATM May 1996 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | ~ IPv4 Datagram ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Pad (0 - 47 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + AAL-5 CPCS-PDU Trailer (8 octets) + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The MTU of an IPv4 datagram using Flow Type 0 encapsulation is 1500 octets. Frames using Flow Type 0 encapsulation are sent to the VPI/VCI specified in the Label field of the corresponding IFMP Flow Type 0 Redirect message element [IFMP]. 4. Flow Type 1 Encapsulation All IPv4 frames using Flow Type 1 are encapsulated directly in the payload of an AAL-5 CPCS-PDU. This is the null encapsulation of section 5.1 "VC based multiplexing of routed protocols" from RFC 1483 [RFC 1483]. There is no LLC/SNAP header. Also, the following fields of the IP header are not transmitted: Version, Internet Header Length (IHL), Type of Service (TOS), Time to Live (TTL), Protocol, Source Address, and Destination Address. In addition, the first 4 octets immediately following the IP header (as determined by the IHL field) are not transmitted. (These 4 octets correspond to the source and destination ports for TCP and UDP datagrams.) The value of the Total Length field is not changed; it remains the total length of the IP datagram before the above fields were removed. The transmitted value of the Checksum field is the checksum value that would have been computed for the entire IP header if the TTL field had been set to zero (i.e., the actual value of the TTL field is "subtracted", using one's-complement arithmetic, from the Checksum before transmission). The IP datagram is encapsulated within the payload of an AAL-5 CPCS- PDU as specified in RFC 1483 and illustrated below: Newman, et. al. Informational PAGE 4 top

RFC 1954 Flow Labelled IPv4 on ATM May 1996 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Total Length | Identification | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Flags| Fragment Offset | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | ~ Data ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Pad (0 - 47 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + AAL-5 CPCS-PDU Trailer (8 octets) + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The MTU of the IPv4 datagram using Flow Type 1 encapsulation is 1484 octets (1500 octets minus the 16 octets specified above). Frames using Flow Type 1 encapsulation are sent to the VPI/VCI specified in the Label field of the corresponding IFMP Flow Type 1 redirect message element [IFMP]. 5. Flow Type 2 Encapsulation All IPv4 frames using Flow Type 2 are encapsulated directly in the payload of an AAL-5 CPCS-PDU. This is the null encapsulation of section 5.1 "VC based multiplexing of routed protocols" from RFC 1483 [RFC 1483]. There is no LLC/SNAP header. Also, the following fields of the IP header are not transmitted: Version, Internet Header Length (IHL), Time to Live (TTL), Source Address, and Destination Address. The first 4 octets immediately following the IP header (as determined by the IHL field) are transmitted. (These 4 octets correspond to the source and destination ports for TCP and UDP datagrams.) The value of the Total Length field is not changed; it remains the total length of the IP datagram before the above fields were removed. The transmitted value of the Checksum field is the checksum value that would have been computed for the entire IP header if the TTL field had been set to zero (i.e., the actual value of the TTL field is "subtracted", using one's-complement arithmetic, from the Checksum before transmission). The IP datagram is encapsulated within the payload of an AAL-5 CPCS- PDU as specified in RFC 1483 and illustrated below: Newman, et. al. Informational PAGE 5 top

RFC 1954 Flow Labelled IPv4 on ATM May 1996 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved |Type of Service| Total Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification |Flags| Fragment Offset | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Protocol | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | ~ Data ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Pad (0 - 47 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + AAL-5 CPCS-PDU Trailer (8 octets) + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The Reserved fields are not used and should be set to zero by the sender and ignored by the receiver. The MTU of the IPv4 datagram using Flow Type 2 encapsulation is 1492 octets (1500 octets minus the 8 octets specified above). Frames using Flow Type 2 encapsulation are sent to the VPI/VCI specified in the Label field of the corresponding IFMP Flow Type 2 redirect message element [IFMP]. Newman, et. al. Informational PAGE 6 top

RFC 1954 Flow Labelled IPv4 on ATM May 1996 References [IFMP] Newman, P., et. al., "Ipsilon Flow Management Protocol Specification for IPv Version 1.0", Ipsilon Networks Inc., RFC 1953, May 1996. [RFC 1483] Heinanen, J., "Multiprotocol Encapsulation over ATM Adaptation Layer 5", RFC 1483, July 1993. SECURITY CONSIDERATIONS Security issues are not discussed in this document. AUTHORS' ADDRESSES Peter Newman Phone: +1 (415) 846-4603 Ipsilon Networks, Inc. EMail: pn@ipsilon.com W. L. Edwards, Chief Scientist Phone: +1 (913) 534 5334 Sprint EMail: texas@sprintcorp.com Robert M. Hinden Phone: +1 (415) 846-4604 Ipsilon Networks, Inc. EMail: hinden@ipsilon.com Eric Hoffman Phone: +1 (415) 846-4610 Ipsilon Networks, Inc. EMail: hoffman@ipsilon.com Fong Ching Liaw Phone: +1 (415) 846-4607 Ipsilon Networks, Inc. EMail: fong@ipsilon.com Tom Lyon Phone: +1 (415) 846-4601 Ipsilon Networks, Inc. EMail: pugs@ipsilon.com Greg Minshall Phone: +1 (415) 846-4605 Ipsilon Networks, Inc. EMail: minshall@ipsilon.com Newman, et. al. Informational PAGE 7 top

RFC 1954 Flow Labelled IPv4 on ATM May 1996 Ipsilon Networks, Inc. is located at: 2191 East Bayshore Road Suite 100 Palo Alto, CA 94303 USA Sprint is located at: Sprint Sprint Technology Services - Long Distance Division 9300 Metcalf Avenue Mailstop KSOPKB0802 Overland Park, KS 66212-6333 USA Newman, et. al. Informational PAGE 8 top

Transmission of Flow Labelled IPv4 on ATM Data Links Ipsilon Version 1.0 RFC TOTAL SIZE: 16075 bytes PUBLICATION DATE: Tuesday, May 21st, 1996 LEGAL RIGHTS: The IETF Trust (see BCP 78)


RFC-ARCHIVE.ORG

© RFC 1954: The IETF Trust, Tuesday, May 21st, 1996
© the RFC Archive, 2024, RFC-Archive.org
Maintainer: J. Tunnissen

Privacy Statement