The RFC Archive
 The RFC Archive   RFC 3145   « Jump to any RFC number directly 
 RFC Home
Full RFC Index
Recent RFCs
RFC Standards
Best Current Practice
RFC Errata
1 April RFC



IETF RFC 3145

L2TP Disconnect Cause Information

Last modified on Saturday, July 14th, 2001

Permanent link to RFC 3145
Search GitHub Wiki for RFC 3145
Show other RFCs mentioning RFC 3145







Network Working Group                                           R. Verma
Request for Comments: 3145                           Deloitte Consulting
Category: Standards Track                                     M. Verma
                                                        3Com Corporation
                                                              J. Carlson
                                                        Sun Microsystems
                                                               July 2001


                   L2TP Disconnect Cause Information

 Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

 Copyright Notice

   Copyright © The Internet Society (2001).  All Rights Reserved.

 Abstract

   This document provides an extension to the Layer 2 Tunneling Protocol
   ("L2TP"), a mechanism for tunneling Point-to-Point Protocol (PPP)
   sessions.  L2TP lacks a mechanism for a host to provide PPP-related
   disconnect cause information to another host.  This information,
   provided by the extension described in this document, can be useful
   for accounting and debugging purposes.

1.  Introduction

   L2TP [1] defines a general-purpose mechanism for tunneling PPP over
   various media.  By design, it insulates L2TP operation from the
   details of the PPP session that is being encapsulated by L2TP.  There
   are, however, cases where it may be desirable for PPP-specific
   disconnect information to be provided to an L2TP host (L2TP Access
   Concentrator [LAC] or L2TP Network Server [LNS]) in a descriptive
   format.  The lack of this information is especially a problem when
   the LAC and LNS are not owned or managed by the same entities.

   The Result and Error Codes defined for L2TP specify only L2TP-
   specific disconnect information.  This document provides an
   additional Attribute Value Pair (AVP), called PPP Disconnect Cause
   Code, that MAY be used by an L2TP host to provide PPP-specific




Verma, et al.               Standards Track                  PAGE 1 top


RFC 3145 L2TP Disconnect Cause Information July 2001 disconnect information to its peer. This AVP should be used in conjunction with, and not as a replacement for, the L2TP Result and Error Code AVPs. The PPP Disconnect Cause Code AVP can also be used to provide a human-readable disconnect reason to the user. This AVP should not have any effect on either the functioning of the tunnel or the functioning of the PPP session; it is for informational and logging purposes only. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [2]. 2. PPP Disconnect Cause Code AVP The AVP is valid in the L2TP Call-Disconnect-Notify (CDN) message only, and it MUST NOT be marked Mandatory. The PPP Disconnect Cause Code AVP is encoded with Vendor ID 0 and an Attribute Type of PPP Disconnect Cause Code (46). The length of the Value field MUST be at least 11 octets. If the length is more than 11 octets, the additional octets MUST contain a descriptive text in UTF-8 [3] format that can be displayed to the user or in a log file. The format of the AVP is shown below. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |M|H| rsvd | Length | Vendor ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Attribute Type | Disconnect Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Control Protocol Number | Direction | Message... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- Figure 1: PPP Disconnect Cause Code AVP Mandatory (M) bit: MUST be 0. Hidden (H) bit: MAY be 1 if the attribute is hidden. Length: The length of the entire attribute in octets, expressed as a single octet. The length MUST be at least 11. Vendor ID: A two octet value in network byte order; set to 0 to indicate that this is an IETF-assigned attribute. Verma, et al. Standards Track PAGE 2 top

RFC 3145 L2TP Disconnect Cause Information July 2001 Attribute Type: A two octet value in network byte order; set to 46 (PPP Disconnect Cause Code). Disconnect Code: A two octet value in network byte order. (Described in section 3 of this document.) Control Protocol Number: The PPP Control Protocol number of the primary protocol known to have caused the error, if any. This field may be 0 unless mentioned otherwise in the description of the Disconnect Codes in section 3. Direction: A single octet value; specifies the direction in which the Disconnect Code applies. The valid values of this field are: 0: global error 1: at peer 2: at local 3-255: Reserved This field SHOULD be 0 unless documented otherwise in the description of the specific Disconnect Code. 3. Disconnect Codes This section contains the list of well-known values of the Disconnect Code field in the PPP Disconnect Cause Code AVP. The IANA will maintain a registry of the up-to-date values (see section 5 of this document). These values should be used in conjunction with the Direction value and the Control Protocol Number field to interpret the specific error condition. Unless documented otherwise for a specific Disconnect Code, the Direction value SHOULD be 0. 3.1. Global Errors The global error codes, given in the list below, are Disconnect Codes that do not relate to one particular PPP Control Protocol. The Control Protocol Number for these errors thus MUST be set to 0. 0 No information available. 1 Administrative disconnect. 2 Link Control Protocol (LCP) renegotiation at LNS disabled; LNS expects proxy LCP information, LAC did not send it. Verma, et al. Standards Track PAGE 3 top

RFC 3145 L2TP Disconnect Cause Information July 2001 3 Normal Disconnection, LCP Terminate-Request sent. Valid Direction values are: 1: LCP Terminate-Request sent by peer 2: LCP Terminate-Request sent by local 4 Compulsory encryption required by a PPP peer was refused by the other. Valid Direction values are: 1: Required by local; refused by peer 2: Required by peer; refused by local 3.2. LCP Errors The LCP error codes, listed below, are disconnect reasons that are directly related to the failure of PPP peers to negotiate mutually agreeable link parameters. The Control Protocol Number for these errors MUST be set to C021 hexadecimal (LCP). 5 FSM (Finite State Machine) Timeout error. (PPP event "TO-".) 6 No recognizable LCP packets were received. 7 LCP failure: Magic Number error; link possibly looped back. 8 LCP link failure: Echo Request timeout. 9 Peer has unexpected Endpoint-Discriminator for existing Multilink PPP (MP) bundle. 10 Peer has unexpected MRRU for existing MP bundle. 11 Peer has unexpected Short-Sequence-Number option for existing MP bundle. 12 Compulsory call-back required by a PPP peer was refused by the other. Valid Direction values are: 1: Required by local; refused by peer 2: Required by peer; refused by local Verma, et al. Standards Track PAGE 4 top

RFC 3145 L2TP Disconnect Cause Information July 2001 3.3. Authentication Errors The authentication error codes, listed below, are disconnect reasons that are directly related to authentication failures between the PPP peers. The Control Protocol Number for such errors MUST correspond to the PPP Control Protocol number for the authentication protocol in use. 13 FSM Timeout error. 14 Peer has unexpected authenticated name for existing MP bundle. 15 PPP authentication failure: Authentication protocol unacceptable. Valid Direction values are: 1: All local authentication protocols were rejected by the peer. 2: All authentication protocols requested by peer were unacceptable or unimplemented locally. 16 PPP authentication failure: Authentication failed (bad name, password, or secret). Valid Direction values are: 1: Authentication of peer identity by local system. 2: Authentication of local identity by peer system. 3.4. Network Control Protocol (NCP) Errors NCP Errors are disconnect reasons that are directly related to the failure of PPP peers to negotiate a mutually agreeable set of parameters for the network protocols. The Control Protocol Number for such errors SHOULD correspond to the PPP Network Control Protocol number in use. Where multiple network protocols are in use, multiple copies of this AVP MAY be given to indicate failure reasons for each NCP. Otherwise, if only one copy of the AVP is given, the Control Protocol Number SHOULD correspond to the last (most recent) failing NCP. 17 FSM Timeout error. 18 No NCPs available (all disabled or rejected); no NCPs went to Opened state. (Control Protocol Number may be zero only if neither peer has enabled NCPs.) Verma, et al. Standards Track PAGE 5 top

RFC 3145 L2TP Disconnect Cause Information July 2001 19 NCP failure: failed to converge on acceptable addresses. Valid Direction values are: 1: Too many Configure-Naks received from peer. 2: Too many Configure-Naks sent to peer. 20 NCP failure: user not permitted to use any addresses. Valid Direction values are: 1: Local link address not acceptable to peer. 2: Remote link address not acceptable to local system. 4. Notes This AVP MAY may be sent by either the LNS or LAC. It is generally expected that this AVP will be most useful in sending notification from the LNS to LAC in the compulsory tunneling case, although it is not precluded from use in any other case. A draft form of this AVP used Vendor ID 43 (3Com Corporation) and vendor-specific Attribute Type 46. Implementations MAY accept AVPs with these values as equivalent to the message described in this document, but SHOULD NOT transmit an AVP using these values. 5. Security Considerations The integrity and confidentiality of this AVP relies on the underlying L2TP security mechanisms. It is intended for logging and diagnostic purposes in the event of PPP link failure and should not pose a threat to system security, but the AVP MAY be hidden as described in section 4.3 of RFC 2661. The defined extension does not provide information that would be useful to an attacker. Future extensions should not be defined to lessen security. For instance, it is inappropriate to provide distinguishing information that would inform the peer that a given authentication name is correct, but the password/secret is incorrect. Verma, et al. Standards Track PAGE 6 top

RFC 3145 L2TP Disconnect Cause Information July 2001 6. IANA Considerations IANA has assigned an L2TP Attribute Type value of 46 for the PPP Disconnect Cause Code defined in Section 2. This AVP includes an enumerated cause code value, called the "Disconnect Code." Values 0 through 20 are described in this document. Values 21 through 32767 (inclusive) are assigned by the IANA subject to IESG Approval. Values 32768 through 65279 (inclusive) are assigned by the IANA on a First Come First Served basis, and are intended for vendor-specific features. Values 65280 through 65535 (inclusive) are allocated for Private or Experimental Use, and no assignment through the IANA is expected. 7. References [1] Townsley, W., Valencia, A., Rubens, A., Pall, G., Zorn, G. and B. Palter, "Layer 2 Tunnel Protocol (L2TP)", RFC 2661, August 1999. [2] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [3] Yergeau, F., "UTF-8, a transformation format of ISO 10646", RFC 2279, January 1998. 8. Acknowledgments The authors thank W. Mark Townsley and Thomas Narten for their comments and help. Verma, et al. Standards Track PAGE 7 top

RFC 3145 L2TP Disconnect Cause Information July 2001 9. Contacts 9.1. L2TP Working Group Chair W. Mark Townsley Cisco Systems 7025 Kit Creek Road PO Box 14987 Research Triangle Park, NC 27709 EMail: townsley@cisco.com 9.2. Authors' Addresses Rohit Verma 180 N. Stetson Avenue Chicago IL 60601 Phone: +1 312 374 2475 Fax: +1 312 870 2475 EMail: rverma@dc.com Madhvi Verma 3800 Golf Road Rolling Meadows IL 60008 Phone: +1 847 262 2987 Fax: +1 847 262 2255 EMail: Madhvi_Verma@3com.com James Carlson Sun Microsystems 1 Network Drive MS UBUR02-212 Burlington MA 01803-2757 Phone: +1 781 442 2084 Fax: +1 781 442 1677 EMail: james.d.carlson@sun.com Verma, et al. Standards Track PAGE 8 top

RFC 3145 L2TP Disconnect Cause Information July 2001 10. Standard Notices 10.1. IETF Intellectual Property Statement The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP 11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights, which may cover technology that, may be required to practice this standard. Please address the information to the IETF Executive Director. Verma, et al. Standards Track PAGE 9 top

RFC 3145 L2TP Disconnect Cause Information July 2001 Full Copyright Statement Copyright © The Internet Society (2001). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society. Verma, et al. Standards Track PAGE 10 top

L2TP Disconnect Cause Information RFC TOTAL SIZE: 17421 bytes PUBLICATION DATE: Saturday, July 14th, 2001 LEGAL RIGHTS: The IETF Trust (see BCP 78)


RFC-ARCHIVE.ORG

© RFC 3145: The IETF Trust, Saturday, July 14th, 2001
© the RFC Archive, 2024, RFC-Archive.org
Maintainer: J. Tunnissen

Privacy Statement