The RFC Archive
 The RFC Archive   RFC 3815   « Jump to any RFC number directly 
 RFC Home
Full RFC Index
Recent RFCs
RFC Standards
Best Current Practice
RFC Errata
1 April RFC



IETF RFC 3815

Definitions of Managed Objects for the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP)

Last modified on Thursday, June 17th, 2004

Permanent link to RFC 3815
Search GitHub Wiki for RFC 3815
Show other RFCs mentioning RFC 3815







Network Working Group                                       J. Cucchiara
Request for Comments: 3815                  Marconi Communications, Inc.
Category: Standards Track                                 H. Sjostrand
                                                             ipUnplugged
                                                              J. Luciani
                                            Marconi Communications, Inc.
                                                               June 2004


                 Definitions of Managed Objects for the
                 Multiprotocol Label Switching (MPLS),
                   Label Distribution Protocol (LDP)

 Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

 Copyright Notice

   Copyright © The Internet Society (2004).

 Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it describes managed objects for the Multiprotocol
   Label Switching, Label Distribution Protocol (LDP).


 Table of Contents

   1.   Introduction. . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.   The Internet-Standard Management Framework. . . . . . . . . .  3
   3.   Structure of the MIB Modules. . . . . . . . . . . . . . . . .  3
        3.1.  Overview. . . . . . . . . . . . . . . . . . . . . . . .  3
        3.2.  Future Considerations . . . . . . . . . . . . . . . . .  4
        3.3.  Interface Indexing. . . . . . . . . . . . . . . . . . .  4
        3.4.  Differences from the LDP Specification. . . . . . . . .  4
        3.5.  The MPLS-LDP-STD-MIB Module . . . . . . . . . . . . . .  5
              3.5.1.  LDP Scalar Objects. . . . . . . . . . . . . . .  5
              3.5.2.  The LDP Entity Table. . . . . . . . . . . . . .  6
                      3.5.2.1.  Changing Values After Session
                                Establishment . . . . . . . . . . . .  6
              3.5.3.  The LDP Entity Statistics Table . . . . . . . .  7



Cucchiara, et al.           Standards Track                  PAGE 1 


RFC 3815 MPLS LDP MIB June 2004 3.5.4. The LDP Peer Table. . . . . . . . . . . . . . . 7 3.5.5. The LDP Session Table . . . . . . . . . . . . . 8 3.5.6. The LDP Session Statistics Table. . . . . . . . 8 3.5.7. The LDP Hello Adjacency Table . . . . . . . . . 8 3.5.8. The LDP LSP Tables. . . . . . . . . . . . . . . 8 3.5.9. The FEC Tables. . . . . . . . . . . . . . . . . 9 3.5.10. The LDP Session Peer Address Table. . . . . . . 9 3.6. LDP Notifications . . . . . . . . . . . . . . . . . . . 9 3.7. LDP Notification Frequency. . . . . . . . . . . . . . . 10 4. MPLS Label Distribution Protocol MIB Definitions. . . . . . . 10 4.1. The MPLS-LDP-ATM-STD-MIB Module . . . . . . . . . . . . 60 4.1.1. The LDP Entity ATM Table. . . . . . . . . . . . 61 4.1.2. The LDP Entity ATM Label Range Table. . . . . . 61 4.1.3. The LDP ATM Session Table . . . . . . . . . . . 61 4.2. The MPLS-LDP-FRAME-RELAY-STD-MIB Module . . . . . . . . 77 4.2.1. The LDP Entity Frame Relay Table. . . . . . . . 77 4.2.2. The LDP Entity Frame Relay Label Range Table. . 77 4.2.3. The LDP Frame Relay Session Table . . . . . . . 77 4.3. The MPLS-LDP-GENERIC-STD-MIB Module . . . . . . . . . . 91 5. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 98 6. References. . . . . . . . . . . . . . . . . . . . . . . . . . 98 6.1. Normative References. . . . . . . . . . . . . . . . . . 98 6.2. Informative References. . . . . . . . . . . . . . . . .100 7. Security Considerations . . . . . . . . . . . . . . . . . . .100 7.1. Security Considerations for MPLS-LDP-STD-MIB. . . . . .100 7.2. Security Considerations for MPLS-LDP-ATM-STD-MIB. . . .101 7.3. Security Considerations for MPLS-LDP-FRAME-RELAY-STD-MIB. . . . . . . . . . . . . .102 7.4. Security Considerations for MPLS-LDP-GENERIC-STD-MIB. .103 7.5. Additional Security Considerations. . . . . . . . . . .103 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . .104 8.1. IANA Considerations for MPLS-LDP-STD-MIB. . . . . . . .104 8.2. IANA Considerations for MPLS-LDP-ATM-STD-MIB. . . . . .104 8.3. IANA Considerations for MPLS-LDP-FRAME-RELAY-STD-MIB. .104 8.4. IANA Considerations for MPLS-LDP-GENERIC-STD-MIB. . . .104 9. Authors' Addresses. . . . . . . . . . . . . . . . . . . . . .105 10. Full Copyright Statement. . . . . . . . . . . . . . . . . . .106 1. Introduction This document defines 4 MIB Modules which together support the configuration and monitoring of the Label Distribution Protocol (LDP). The Label Distribution Protocol (LDP) [RFC 3036] is one type of Multiprotocol Label Switching (MPLS) protocols described in [RFC 3031] and [RFC 3032]. Utilizing all 4 MIB Modules allows an operator to configure LDP sessions using 3 different Layer 2 media. The Layer 2 media supported by the MIB Modules are Ethernet, ATM and Frame Relay as described in [RFC 3036], [RFC 3034] and [RFC 3035]. Cucchiara, et al. Standards Track PAGE 2

RFC 3815 MPLS LDP MIB June 2004 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC 2119]. For an introduction to the concepts of MPLS, see [RFC 3031]. For further on LDP refer to [RFC 3037] and [RFC 3215]. 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC 3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC 2578], STD 58, RFC 2579 [RFC 2579] and STD 58, RFC 2580 [RFC 2580]. 3. Structure of the MIB Modules This section describes the structure of the LDP MIB Modules. 3.1. Overview There are 4 MIB Modules in this document. These MIB Modules are the MPLS-LDP-STD-MIB, the MPLS-LDP-GENERIC-STD-MIB, the MPLS-LDP-ATM-STD- MIB and the MPLS-LDP-FRAME-RELAY-STD-MIB. The MPLS-LDP-STD-MIB defines objects which are common to all LDP implementations. The MPLS-LDP-GENERIC-STD-MIB defines Layer 2 Per Platform Label Space objects for use with the MPLS-LDP-STD-MIB. The MPLS-LDP-ATM-STD-MIB defines Layer 2 Asynchronous Transfer Mode (ATM) objects for use with the MPLS-LDP-STD-MIB. The MPLS-LDP-FRAME-RELAY-STD-MIB defines Layer 2 FRAME-RELAY objects for use with the MPLS-LDP-STD-MIB. The MPLS-LDP-STD-MIB Module MUST be implemented and at least one of the Layer 2 MIB Modules MUST be implemented by an Agent developer on an Label Switching Router (LSR) or Label Edge Router (LER). As an example, if a Label Switching Router (LSR) or Label Edge Router (LER) implementation intends to support LDP utilizing a Layer 2 of Ethernet, then the MPLS-LDP-STD-MIB and the MPLS-LDP-GENERIC-STD-MIB Modules MUST implemented. If an LSR/LER implementation intends to support LDP utilizing a Layer 2 of ATM, then the MPLS-LDP-STD-MIB Module and the MPLS-LDP-ATM-MIB Module MUST be implemented. If an LSR/LER implementation intends to support LDP utilizing a Layer 2 of Cucchiara, et al. Standards Track PAGE 3

RFC 3815 MPLS LDP MIB June 2004 FRAME-RELAY, then the MPLS-LDP-STD-MIB Module and the MPLS-LDP-FRAME- RELAY-STD-MIB Module MUST be implemented. An LDP implementation that utilizes all three Layer 2 media (Ethernet, Frame-Relay, ATM) MUST support all 4 MIB Modules. Each of the Modules will be discussed in detail in the following sections. There are 2 compliance statements for each MIB Module. One compliance statement is for full compliance which allows both configuration and monitoring via SNMP. The other compliance statement is for read-only compliance which allows only monitoring via SNMP. 3.2. Future Considerations The LDP Specification [RFC 3036] does not specify the use of VPNs or multicast for LDP, and thus, objects related to these areas have not been included. [RFC 2684] does not describe VP merge capability and so this feature has not been included. These areas need to be specified in the LDP Specification or other specifications prior to being added in this or any other MIB document. 3.3. Interface Indexing Interface Indexes as specified in [RFC 2863] are used in these MIB Modules. The descriptions of the ifIndexes denote which ifIndex is being used. The use of ifIndex is for actual existing connections. 3.4. Differences from the LDP Specification Currently, there are 3 differences between this specification and the LDP Specification. As described in the Introduction, this document is almost entirely based on the LDP specification. The differences are documented here. The first difference is that the LDP Entity Table contains some DEFVAL clauses which are not specified explicitly in the LDP Specification. These values, although not documented in the LDP Specification, are widely used by existing LDP MIB implementations and thus, have been adopted within this MPLS-LDP-STD-MIB module. Please note, they can certainly be changed during row creation or a subsequent SET request. Cucchiara, et al. Standards Track PAGE 4

RFC 3815 MPLS LDP MIB June 2004 A second difference is the mplsLdpEntityGenericLRTable in the MPLS- LDP-GENERIC-STD-MIB Module. This table, although provided as a way to reserve a range of generic labels, does not exist in the LDP Specification. It was added to the MIB due to a request from the working group and because this table was considered useful for reserving a range of generic labels. The third difference is documented by the TEXTUAL-CONVENTION, MplsAtmVcIdentifier which is in the MPLS-TC-STD-MIB [RFC 3811]. This TC was added to restrict vci values to be greater than 31 as described in RFC 3035 [RFC 3035]. 3.5. The MPLS-LDP-STD-MIB Module This MIB Module contains objects which are common to all LDP implementations. This MIB Module MUST always be implemented along with one or more of the Layer 2 MIB Modules. This MIB Module IMPORTS IndexInteger and IndexIntegerNextFree TEXTUAL-CONVENTIONs from [RFC 3289], and IMPORTS InetAddressPrefixLength, InetAddressType, InetAddressInetPortNumber TEXTUAL-CONVENTIONs from [RFC 3291]. The mplsLdpEntityTable table allows the Label Edge Router (LER) or the Label Switching Router (LSR) to initiate and/or receive requests to establish LDP sessions. As the LDP protocol distributes labels and establishes sessions with Peers most of the tables in this module are populated by the agent as instructed by the LDP protocol. The exception is the mplsFecTable and the mplsLdpLspFecTable which can be configured by the operator to specify Forwarding Equivalence Class information for an LSP. Some scalars and each table in the MPLS-LDP-STD-MIB Module are described in the following subsections. 3.5.1. LDP Scalar Objects There are several scalar objects in the LDP MIB module. The mplsLdpLsrId is a read-only scalar object which reports Label Switching Router's (LSR's) Identifier. This MUST be a globally unique value, such as the 32-bit router ID assigned to the LSR. The mplsLdpLsrLoopDetectionCapable scalar object denotes whether the LSR is capable of supporting loop detection and if so, which form of loop detection. Cucchiara, et al. Standards Track PAGE 5

RFC 3815 MPLS LDP MIB June 2004 There are two LastChange scalar objects, mplsLdpEntityLastChange and mplsLdpPeerLastChange. These objects give an indication of there was a change in the number of entries in the table, or if any of the values in the respective tables changed. Please see the object's description for more details. The mplsLdpEntityIndexNext scalar object is described in the next section. 3.5.2. The LDP Entity Table The MPLS-LDP-STD-MIB provides objects to configure/set-up potential LDP sessions on a specific LSR/LER. The mplsLdpEntityTable is used to configure information which is used by the LDP protocol to setup potential LDP Sessions. Each entry/row in this table represents a single LDP Entity. There is no maximum number of LDP Entities specified. However, there is an mplsLdpEntityIndexNext object which should be retrieved by the command generator prior to creating an LDP Entity. If the mplsLdpEntityIndexNext object is zero, this indicates that the LSR/LER is not able to create another LDP Entity at that time. 3.5.2.1. Changing Values After Session Establishment One way to manually modify a session's parameters is by using SNMP to change the MIB objects related to that session. Please note, special care should be taken if MIB objects which are used in the MPLS LDP Session Initialization need to be modified. If the modification of any of these MIB variables takes place anytime after the start of session intialization, then the entire session must be halted. Any information learned by that session must be discarded. The objects should then be modified, and session initialization started. Assuming that the configuration was done correctly, then a new session will be created. For example, assume that an operator wishes to change the configuration of a Label Range which is used by a Session that has already been established. The operator should change the mplsLdpEntityAdminStatus to "disable(2)". Setting the mplsLdpEntityAdminStatus to "disable(2)" will cause the session to be torn down (i.e., this will signal to LDP that it should send out tear down messages for that session). Also, all information related to that session should be removed from this MIB by the Agent. This includes Peer information (i.e., relevant row in the mplsPeerTable) and Session statistics (i.e., relevant row in the mplsLdpSessionTable). Also, if the MPLS-LSR-STD-MIB module [RFC 3813] is implemented and the optional Mapping Table objects are Cucchiara, et al. Standards Track PAGE 6

RFC 3815 MPLS LDP MIB June 2004 implemented, then all information related to the LSPs in this session should be removed from these MIB modules. [For more information please see the section on "The Mapping Tables".] At this point, the operator could modify the Label Range. Lastly, the operator should set the mplsLdpEntityAdminStatus to "enable(1)". At this point session initialization should occur. The LDP Entity goes through the Session Initialization in order to communicate the new Label Ranges to the Peer and establish new LSPs. 3.5.3. The LDP Entity Statistics Table The mplsLpdEntityStatsTable is a read-only table which contains statistical information related to failed attempts to establish sessions. Each row in this table AUGMENTS an mplsLdpEntityEntry. This table could be used to give insight into how to reconfigure values so that a session could be successfully established. For example, if the mplsLdpEntityStatsSessionRejectedLRErrors Counter object was increasing, then this would indicate that the Label Range (LR) may need to be adjusted. 3.5.4. The LDP Peer Table The mplsLdpPeerTable is a read-only table which contains information about LDP Peers known to LDP Entities. In other words, the Peer information is learned by LDP through initialization or discovery. This table should be populated by the agent as directed by the LDP protocol. A row in this table is related to one or more rows in the Hello Adjacency Table and related to a single row in the Session Table. The values in the Peer table are specific to a Peer and may or may not be the same values used in the session. The reason is that the Peer and Entity negotiate certain values. The Entity's values are configured in the mplsLdpEntityTable and the Peer's values are learned (and placed into the mplsLdpPeerTable). The mplsLdpSessionTable shows the values used in establishing the session. One example, of when the Peer's values and the Session's values may differ is with the Peer's Path Limit information. The Peer's Path Limit information is learned from the session initialization phase. The actual value for the Path Vector Limit is the Peer's value and may not be the same value that appears in the session. There could be a mismatch in this value between the Entity and the Peer. In the event of a mismatch, then the session will use the Path Limit set by the Entity (and not the Peer). Cucchiara, et al. Standards Track PAGE 7

RFC 3815 MPLS LDP MIB June 2004 The Peer Table information was placed in a separate table from the Session information to allow for a more comprehensive and coherent MIB model. 3.5.5. The LDP Session Table The mplsLdpSessionTable is a read-only table. Each entry in this table represents a single session between an LDP Entity and a Peer. The mplsLdpSessionEntry AUGMENTS the mplsLdpPeerEntry. The information in this table is learned during session establishment. NOTE: rows in this table will appear during session intialization. 3.5.6. The LDP Session Statistics Table The mplsLdpSessionStatsTable is a read-only table which contains statistical information on sessions. This table AUGMENTS the mplsLdpPeerTable. 3.5.7. The LDP Hello Adjacency Table This is a table of all adjacencies between all LDP Entities and all LDP Peers. A Session may have one or more adjacencies. A session should not have zero adjacencies, because this indicates that the session has lost contact with the Peer. A session which has zero Hello Adjacencies should be removed. 3.5.8. The LDP LSP Tables The Label Information Base (LIB) contains information about labels learned by the LSR. The LIB for LDP, CR-LDP and MPLS-RSVP (i.e., all currently defined MPLS protocols) is represented in the LSR MIB [RFC 3813]. The LIB is represented by the LSR MIB's mplsXCTable (mpls Cross Connect Table), mplsInSegmentTable (mpls In Segment Table) and the mplsOutSegmentTable (mpls Out Segment Table). The mplsXCTable models the cross-connection of the incoming label with a specific outgoing label. The mplsInSegmentTable stores the incoming label's information, and the mplsOutSegmentTable stores the outgoing label's information. The LDP Session that created the LSP and the LSP's (incoming label, outgoing label) pair along with other information is contained in the MPLS-LSR-STD-MIB module's mplsXCTable, the mplsInSegmentTable and the mplsOutSegmentTable. Cucchiara, et al. Standards Track PAGE 8

RFC 3815 MPLS LDP MIB June 2004 In order to utilize the MPLS-LSR-STD-MIB module's mplsXCTable, mplsInSegmentTable and mplsOutSegmentTable for LDP LSPs, there needs to be a mechanism to associate LDP sessions with LDP LSPs created as a result of those LDP sessions. The mplsInSegmentLdpLspTable and mplsOutSegmentLdpLspTable in this MIB contain information to find the LDP LSP entries in the mplsInSegmentTable, mplsOutSegmentTable and the mplsXCTable. These two tables, the mplsInSegmentLdpLspTable and mplsOutSegmentLdpLspTable, have been made optional in the conformance section of the MIB. They only need to be supported if the LSR MIBs mplsInSegmentTable, mplsOutSegmentTable and mplsXCTable are implemented. As discussed in the section, "Changing Values after Session Establishment", if a session is torn down, then all the information related to this session, must be removed from the both LDP MIB and, if implemented, from the LSR MIB. 3.5.9. The FEC Tables The mplsLdpFecTable is a table which contains FEC (Forwarding Equivalence Class) information. Each entry/row represents a single FEC Element. There is also an LDP LSP FEC Table, mplsLdpLspFecTable, which associates FECs with the LSPs. 3.5.10. The LDP Session Peer Address Table The mplsLdpSessionPeerAddrTable is a table which extends the mplsLdpSessionTable. This table is a read-only table which stores Addresses learned after session initialization via Address Message advertisement. 3.6. LDP Notifications Currently, there are several notifications which are specific for LDP. These are described in this section. There are no objects which enable or disable notifications from being generated. RFC 3413 [RFC 3413] contains MIB modules which can be implemented that will enable or disable these notifications from being generated. The mplsLdpInitSessionThresholdExceeded notification indicates to the operator that there may be a misconfigured mplsLdpEntityEntry because the session associated with this Entity is not being established, and the Entity keeps trying to establish the session. A side effect of this situation is that a row in the mplsLdpSessionTable may not be reaching the operational state as indicated by the mplsLdpSessionState object. If the value of Cucchiara, et al. Standards Track PAGE 9

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityInitSessionThreshold is 0 (zero) then this is equal to specifying the value of infinity for the threshold, and the mplsLdpInitSessionThresholdExceeded notification will never be sent. The mplsLdpPathVectorLimitMismatch notification is generated when there is a mismatch in the Path Vector Limits between the Entity and Peer during session initialization. The session uses the value which is configured as the Entity's Path Vector Limit. However, a notification should be generated to indicate that a mismatch occurred. For further details, please see Section 3.5.3 of the LDP Specification [RFC 3036]. The mplsLdpSessionUp and mplsLdpSessionDown notifications are generated when there is an appropriate change in the mplsLdpSessionState object, e.g., when sessions change state (Up to Down for the mplsLdpSessionDown notification, or Down to Up for the mplsLdpSessionUp notification). There was discussion about combining these two notifications into a single notification, however, some NMS applications can utilize two different notifications, rather than having to parse the varbind list of a single notification. For example, the SessionDown is matched to a SessionUp notification more easily by some NMS applications, than having to parse a Varbind list in a SessionChange type of notification. 3.7. LDP Notification Frequency LDP Notifications are expected to be few in number when LDP is ubiquitously deployed in a relatively stable network. A notification receiver, e.g., an NMS, that receives these notifications should not be overwhelmed by the frequency of LDP notifications. If this assertion proves to be inaccurate, then a throttling object to throttle these notifications may be added to future versions of the MPLS-LDP-STD-MIB. 4. MPLS Label Distribution Protocol MIB Definitions MPLS-LDP-STD-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, Integer32, Counter32, Unsigned32 FROM SNMPv2-SMI -- [RFC 2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC 2580] RowStatus, TimeInterval, TruthValue, TimeStamp, StorageType Cucchiara, et al. Standards Track PAGE 10

RFC 3815 MPLS LDP MIB June 2004 FROM SNMPv2-TC -- [RFC 2579] InetAddressPrefixLength, InetAddressType, InetAddress, InetPortNumber FROM INET-ADDRESS-MIB -- [RFC 3291] IndexInteger, IndexIntegerNextFree FROM DIFFSERV-MIB -- [RFC 3289] mplsStdMIB, MplsLabelDistributionMethod, MplsLdpIdentifier, MplsLdpLabelType, MplsLspType, MplsLsrIdentifier, MplsRetentionMode FROM MPLS-TC-STD-MIB -- [RFC 3811] MplsIndexType FROM MPLS-LSR-STD-MIB; -- [RFC 3813] mplsLdpStdMIB MODULE-IDENTITY LAST-UPDATED "200406030000Z" -- June 3, 2004 ORGANIZATION "Multiprotocol Label Switching (mpls) Working Group" CONTACT-INFO "Joan Cucchiara (jcucchiara@mindspring.com) Marconi Communications, Inc. Hans Sjostrand (hans@ipunplugged.com) ipUnplugged James V. Luciani (james_luciani@mindspring.com) Marconi Communications, Inc. Working Group Chairs: George Swallow, email: swallow@cisco.com Loa Andersson, email: loa@pi.se MPLS Working Group, email: mpls@uu.net" DESCRIPTION "Copyright © The Internet Society (2004). The initial version of this MIB module was published Cucchiara, et al. Standards Track PAGE 11

RFC 3815 MPLS LDP MIB June 2004 in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for the 'Multiprotocol Label Switching, Label Distribution Protocol, LDP' document." REVISION "200406030000Z" -- June 3, 2004 DESCRIPTION "Initial version published as part of RFC 3815." ::= { mplsStdMIB 4 } --**************************************************************** mplsLdpNotifications OBJECT IDENTIFIER ::= { mplsLdpStdMIB 0 } mplsLdpObjects OBJECT IDENTIFIER ::= { mplsLdpStdMIB 1 } mplsLdpConformance OBJECT IDENTIFIER ::= { mplsLdpStdMIB 2 } --**************************************************************** -- MPLS LDP Objects --**************************************************************** mplsLdpLsrObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 1 } mplsLdpEntityObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 2 } -- -- The MPLS Label Distribution Protocol's -- Label Switching Router Objects -- mplsLdpLsrId OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The Label Switching Router's Identifier." ::= { mplsLdpLsrObjects 1 } mplsLdpLsrLoopDetectionCapable OBJECT-TYPE SYNTAX INTEGER { none(1), other(2), hopCount(3), pathVector(4), hopCountAndPathVector(5) Cucchiara, et al. Standards Track PAGE 12

RFC 3815 MPLS LDP MIB June 2004 } MAX-ACCESS read-only STATUS current DESCRIPTION "A indication of whether this Label Switching Router supports loop detection. none(1) -- Loop Detection is not supported on this LSR. other(2) -- Loop Detection is supported but by a method other than those listed below. hopCount(3) -- Loop Detection is supported by Hop Count only. pathVector(4) -- Loop Detection is supported by Path Vector only. hopCountAndPathVector(5) -- Loop Detection is supported by both Hop Count And Path Vector. Since Loop Detection is determined during Session Initialization, an individual session may not be running with loop detection. This object simply gives an indication of whether or not the LSR has the ability to support Loop Detection and which types." ::= { mplsLdpLsrObjects 2 } -- -- The MPLS Label Distribution Protocol Entity Objects -- mplsLdpEntityLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the most recent addition or deletion of an entry to/from the mplsLdpEntityTable/mplsLdpEntityStatsTable, or the most recent change in value of any objects in the mplsLdpEntityTable. Cucchiara, et al. Standards Track PAGE 13

RFC 3815 MPLS LDP MIB June 2004 If no such changes have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { mplsLdpEntityObjects 1 } mplsLdpEntityIndexNext OBJECT-TYPE SYNTAX IndexIntegerNextFree MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for mplsLdpEntityIndex when creating entries in the mplsLdpEntityTable. The value 0 indicates that no unassigned entries are available." ::= { mplsLdpEntityObjects 2 } mplsLdpEntityTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switching Router (LSR) or Label Edge Router (LER)." ::= { mplsLdpEntityObjects 3 } mplsLdpEntityEntry OBJECT-TYPE SYNTAX MplsLdpEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents an LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex } ::= { mplsLdpEntityTable 1 } MplsLdpEntityEntry ::= SEQUENCE { mplsLdpEntityLdpId MplsLdpIdentifier, mplsLdpEntityIndex IndexInteger, mplsLdpEntityProtocolVersion Unsigned32, mplsLdpEntityAdminStatus INTEGER, mplsLdpEntityOperStatus INTEGER, mplsLdpEntityTcpPort InetPortNumber, mplsLdpEntityUdpDscPort InetPortNumber, Cucchiara, et al. Standards Track PAGE 14

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityMaxPduLength Unsigned32, mplsLdpEntityKeepAliveHoldTimer Unsigned32, mplsLdpEntityHelloHoldTimer Unsigned32, mplsLdpEntityInitSessionThreshold Integer32, mplsLdpEntityLabelDistMethod MplsLabelDistributionMethod, mplsLdpEntityLabelRetentionMode MplsRetentionMode, mplsLdpEntityPathVectorLimit Integer32, mplsLdpEntityHopCountLimit Integer32, mplsLdpEntityTransportAddrKind INTEGER, mplsLdpEntityTargetPeer TruthValue, mplsLdpEntityTargetPeerAddrType InetAddressType, mplsLdpEntityTargetPeerAddr InetAddress, mplsLdpEntityLabelType MplsLdpLabelType, mplsLdpEntityDiscontinuityTime TimeStamp, mplsLdpEntityStorageType StorageType, mplsLdpEntityRowStatus RowStatus } mplsLdpEntityLdpId OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The LDP identifier." REFERENCE "RFC 3036, LDP Specification, Section on LDP Identifiers." ::= { mplsLdpEntityEntry 1 } mplsLdpEntityIndex OBJECT-TYPE SYNTAX IndexInteger MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index is used as a secondary index to uniquely identify this row. Before creating a row in this table, the 'mplsLdpEntityIndexNext' object should be retrieved. That value should be used for the value of this index when creating a row in this table. NOTE: if a value of zero (0) is retrieved, that indicates that no rows can be created in this table at this time. A secondary index (this object) is meaningful to some but not all, LDP implementations. For example an LDP implementation which uses PPP would use this index to differentiate PPP sub-links. Another way to use this index is to give this the value of ifIndex. However, this is dependant Cucchiara, et al. Standards Track PAGE 15

RFC 3815 MPLS LDP MIB June 2004 on the implementation." ::= { mplsLdpEntityEntry 2 } mplsLdpEntityProtocolVersion OBJECT-TYPE SYNTAX Unsigned32(1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The version number of the LDP protocol which will be used in the session initialization message. Section 3.5.3 in the LDP Specification specifies that the version of the LDP protocol is negotiated during session establishment. The value of this object represents the value that is sent in the initialization message." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3 Initialization Message." DEFVAL { 1 } ::= { mplsLdpEntityEntry 3 } mplsLdpEntityAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative status of this LDP Entity. If this object is changed from 'enable' to 'disable' and this entity has already attempted to establish contact with a Peer, then all contact with that Peer is lost and all information from that Peer needs to be removed from the MIB. (This implies that the network management subsystem should clean up any related entry in the mplsLdpPeerTable. This further implies that a 'tear-down' for that session is issued and the session and all information related to that session cease to exist). At this point the operator is able to change values which are related to this entity. When the admin status is set back to 'enable', then this Entity will attempt to establish a new session with the Peer." Cucchiara, et al. Standards Track PAGE 16

RFC 3815 MPLS LDP MIB June 2004 DEFVAL { enable } ::= { mplsLdpEntityEntry 4 } mplsLdpEntityOperStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of this LDP Entity. The value of unknown(1) indicates that the operational status cannot be determined at this time. The value of unknown should be a transient condition before changing to enabled(2) or disabled(3)." ::= { mplsLdpEntityEntry 5 } mplsLdpEntityTcpPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The TCP Port for LDP. The default value is the well-known value of this port." REFERENCE "RFC 3036, LDP Specification, Section 3.10, Well-known Numbers, and Section 3.10.1. UDP and TCP Ports." DEFVAL { 646 } ::= { mplsLdpEntityEntry 6 } mplsLdpEntityUdpDscPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The UDP Discovery Port for LDP. The default value is the well-known value for this port." REFERENCE "RFC 3036, LDP Specification, Section 2.4.1, Basic Discovery Mechanism, Section 2.4.2, Extended Discovery Mechanism, Section 3.10, Well-known Numbers, and Section 3.10.1. Cucchiara, et al. Standards Track PAGE 17

RFC 3815 MPLS LDP MIB June 2004 UDP and TCP Ports." DEFVAL { 646 } ::= { mplsLdpEntityEntry 7 } mplsLdpEntityMaxPduLength OBJECT-TYPE SYNTAX Unsigned32 (256..65535) UNITS "octets" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum PDU Length that is sent in the Common Session Parameters of an Initialization Message. According to the LDP Specification [RFC 3036] a value of 255 or less specifies the default maximum length of 4096 octets, this is why the value of this object starts at 256. The operator should explicitly choose the default value (i.e., 4096), or some other value. The receiving LSR MUST calculate the maximum PDU length for the session by using the smaller of its and its peer's proposals for Max PDU Length." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3. Initialization Message." DEFVAL { 4096 } ::= { mplsLdpEntityEntry 8 } mplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The 16-bit integer value which is the proposed keep alive hold timer for this LDP Entity." DEFVAL { 40 } ::= { mplsLdpEntityEntry 9 } mplsLdpEntityHelloHoldTimer OBJECT-TYPE SYNTAX Unsigned32 (0..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The 16-bit integer value which is the proposed Hello hold timer for this LDP Entity. The Hello Hold time in seconds. Cucchiara, et al. Standards Track PAGE 18

RFC 3815 MPLS LDP MIB June 2004 An LSR maintains a record of Hellos received from potential peers. This object represents the Hold Time in the Common Hello Parameters TLV of the Hello Message. A value of 0 is a default value and should be interpretted in conjunction with the mplsLdpEntityTargetPeer object. If the value of this object is 0: if the value of the mplsLdpEntityTargetPeer object is false(2), then this specifies that the Hold Time's actual default value is 15 seconds (i.e., the default Hold time for Link Hellos is 15 seconds). Otherwise if the value of the mplsLdpEntityTargetPeer object is true(1), then this specifies that the Hold Time's actual default value is 45 seconds (i.e., the default Hold time for Targeted Hellos is 45 seconds). A value of 65535 means infinite (i.e., wait forever). All other values represent the amount of time in seconds to wait for a Hello Message. Setting the hold time to a value smaller than 15 is not recommended, although not forbidden according to RFC 3036." REFERENCE "RFC 3036, LDP Specification, Section 3.5.2., Hello Message." DEFVAL { 0 } ::= { mplsLdpEntityEntry 10 } mplsLdpEntityInitSessionThreshold OBJECT-TYPE SYNTAX Integer32(0..100) MAX-ACCESS read-create STATUS current DESCRIPTION "When attempting to establish a session with a given Peer, the given LDP Entity should send out the SNMP notification, 'mplsLdpInitSessionThresholdExceeded', when the number of Session Initialization messages sent exceeds this threshold. The notification is used to notify an operator when this Entity and its Peer are possibly engaged in an endless sequence of messages as each NAKs the other's Cucchiara, et al. Standards Track PAGE 19

RFC 3815 MPLS LDP MIB June 2004 Initialization messages with Error Notification messages. Setting this threshold which triggers the notification is one way to notify the operator. The notification should be generated each time this threshold is exceeded and for every subsequent Initialization message which is NAK'd with an Error Notification message after this threshold is exceeded. A value of 0 (zero) for this object indicates that the threshold is infinity, thus the SNMP notification will never be generated." REFERENCE "RFC 3036, LDP Specification, Section 2.5.3 Session Initialization." DEFVAL { 8 } ::= { mplsLdpEntityEntry 11 } mplsLdpEntityLabelDistMethod OBJECT-TYPE SYNTAX MplsLabelDistributionMethod MAX-ACCESS read-create STATUS current DESCRIPTION "For any given LDP session, the method of label distribution must be specified." ::= { mplsLdpEntityEntry 12 } mplsLdpEntityLabelRetentionMode OBJECT-TYPE SYNTAX MplsRetentionMode MAX-ACCESS read-create STATUS current DESCRIPTION "The LDP Entity can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized label mappings are retained only if they will be used to forward packets, i.e., if label came from a valid next hop. If the value of this object is liberal(2) then all advertized label mappings are retained whether they are from a valid next hop or not." ::= { mplsLdpEntityEntry 13 } mplsLdpEntityPathVectorLimit OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create Cucchiara, et al. Standards Track PAGE 20

RFC 3815 MPLS LDP MIB June 2004 STATUS current DESCRIPTION "If the value of this object is 0 (zero) then Loop Detection for Path Vectors is disabled. Otherwise, if this object has a value greater than zero, then Loop Dection for Path Vectors is enabled, and the Path Vector Limit is this value. Also, the value of the object, 'mplsLdpLsrLoopDetectionCapable', must be set to either 'pathVector(4)' or 'hopCountAndPathVector(5)', if this object has a value greater than 0 (zero), otherwise it is ignored." REFERENCE "RFC 3036, LDP Specification, Section 2.8 Loop Dection, Section 3.4.5 Path Vector TLV." ::= { mplsLdpEntityEntry 14 } mplsLdpEntityHopCountLimit OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of this object is 0 (zero), then Loop Detection using Hop Counters is disabled. If the value of this object is greater than 0 (zero) then Loop Detection using Hop Counters is enabled, and this object specifies this Entity's maximum allowable value for the Hop Count. Also, the value of the object mplsLdpLsrLoopDetectionCapable must be set to either 'hopCount(3)' or 'hopCountAndPathVector(5)' if this object has a value greater than 0 (zero), otherwise it is ignored." DEFVAL { 0 } ::= { mplsLdpEntityEntry 15 } mplsLdpEntityTransportAddrKind OBJECT-TYPE SYNTAX INTEGER { interface(1), loopback(2) } MAX-ACCESS read-create STATUS current Cucchiara, et al. Standards Track PAGE 21

RFC 3815 MPLS LDP MIB June 2004 DESCRIPTION "This specifies whether the loopback or interface address is to be used as the transport address in the transport address TLV of the hello message. If the value is interface(1), then the IP address of the interface from which hello messages are sent is used as the transport address in the hello message. Otherwise, if the value is loopback(2), then the IP address of the loopback interface is used as the transport address in the hello message." DEFVAL { loopback } ::= { mplsLdpEntityEntry 16 } mplsLdpEntityTargetPeer OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If this LDP entity uses targeted peer then set this to true." DEFVAL { false } ::= { mplsLdpEntityEntry 17 } mplsLdpEntityTargetPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the internetwork layer address used for the Extended Discovery. This object indicates how the value of mplsLdpEntityTargetPeerAddr is to be interpreted." ::= { mplsLdpEntityEntry 18 } mplsLdpEntityTargetPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the internetwork layer address used for the Extended Discovery. The value of mplsLdpEntityTargetPeerAddrType specifies how this address is to be interpreted." ::= { mplsLdpEntityEntry 19 } Cucchiara, et al. Standards Track PAGE 22

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityLabelType OBJECT-TYPE SYNTAX MplsLdpLabelType MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the optional parameters for the LDP Initialization Message. If the value is generic(1) then no optional parameters will be sent in the LDP Initialization message associated with this Entity. If the value is atmParameters(2) then a row must be created in the mplsLdpEntityAtmTable, which corresponds to this entry. If the value is frameRelayParameters(3) then a row must be created in the mplsLdpEntityFrameRelayTable, which corresponds to this entry." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3., Initialization Message." ::= { mplsLdpEntityEntry 20 } mplsLdpEntityDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this entity's counters suffered a discontinuity. The relevant counters are the specific instances associated with this entity of any Counter32 object contained in the 'mplsLdpEntityStatsTable'. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { mplsLdpEntityEntry 21 } mplsLdpEntityStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current Cucchiara, et al. Standards Track PAGE 23

RFC 3815 MPLS LDP MIB June 2004 DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL{ nonVolatile } ::= { mplsLdpEntityEntry 22 } mplsLdpEntityRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable, which enables a new session to be initiated." ::= { mplsLdpEntityEntry 23 } -- -- The MPLS LDP Entity Statistics Table -- mplsLdpEntityStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is a read-only table which augments the mplsLdpEntityTable. The purpose of this table is to keep statistical information about the LDP Entities on the LSR." ::= { mplsLdpEntityObjects 4 } mplsLdpEntityStatsEntry OBJECT-TYPE SYNTAX MplsLdpEntityStatsEntry Cucchiara, et al. Standards Track PAGE 24

RFC 3815 MPLS LDP MIB June 2004 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table contains statistical information about an LDP Entity. Some counters contained in a row are for fatal errors received during a former LDP Session associated with this entry. For example, an LDP PDU received on a TCP connection during an LDP Session contains a fatal error. That error is counted here, because the session is terminated. If the error is NOT fatal (i.e., the Session remains), then the error is counted in the mplsLdpSessionStatsEntry." AUGMENTS { mplsLdpEntityEntry } ::= { mplsLdpEntityStatsTable 1 } MplsLdpEntityStatsEntry ::= SEQUENCE { mplsLdpEntityStatsSessionAttempts Counter32, mplsLdpEntityStatsSessionRejectedNoHelloErrors Counter32, mplsLdpEntityStatsSessionRejectedAdErrors Counter32, mplsLdpEntityStatsSessionRejectedMaxPduErrors Counter32, mplsLdpEntityStatsSessionRejectedLRErrors Counter32, mplsLdpEntityStatsBadLdpIdentifierErrors Counter32, mplsLdpEntityStatsBadPduLengthErrors Counter32, mplsLdpEntityStatsBadMessageLengthErrors Counter32, mplsLdpEntityStatsBadTlvLengthErrors Counter32, mplsLdpEntityStatsMalformedTlvValueErrors Counter32, mplsLdpEntityStatsKeepAliveTimerExpErrors Counter32, mplsLdpEntityStatsShutdownReceivedNotifications Counter32, mplsLdpEntityStatsShutdownSentNotifications Counter32 } mplsLdpEntityStatsSessionAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Initialization messages which were sent or received by this LDP Entity and were NAK'd. In other words, this counter counts the number of session initializations that failed. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." Cucchiara, et al. Standards Track PAGE 25

RFC 3815 MPLS LDP MIB June 2004 ::= { mplsLdpEntityStatsEntry 1 } mplsLdpEntityStatsSessionRejectedNoHelloErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Rejected/No Hello Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 2 } mplsLdpEntityStatsSessionRejectedAdErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Rejected/Parameters Advertisement Mode Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 3 } mplsLdpEntityStatsSessionRejectedMaxPduErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Rejected/Parameters Max Pdu Length Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 4 } Cucchiara, et al. Standards Track PAGE 26

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityStatsSessionRejectedLRErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the Session Rejected/Parameters Label Range Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 5 } mplsLdpEntityStatsBadLdpIdentifierErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Bad LDP Identifier Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC 3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 6 } mplsLdpEntityStatsBadPduLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Bad PDU Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC 3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 7 } Cucchiara, et al. Standards Track PAGE 27

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityStatsBadMessageLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Bad Message Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC 3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 8 } mplsLdpEntityStatsBadTlvLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Bad TLV Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC 3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 9 } mplsLdpEntityStatsMalformedTlvValueErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Malformed TLV Value Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." Cucchiara, et al. Standards Track PAGE 28

RFC 3815 MPLS LDP MIB June 2004 REFERENCE "RFC 3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 10 } mplsLdpEntityStatsKeepAliveTimerExpErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Session Keep Alive Timer Expired Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." REFERENCE "RFC 3036, LDP Specification, Section 3.5.1.2." ::= { mplsLdpEntityStatsEntry 11 } mplsLdpEntityStatsShutdownReceivedNotifications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Shutdown Notifications received related to session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 12 } mplsLdpEntityStatsShutdownSentNotifications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Shutdown Notfications sent related to session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of Cucchiara, et al. Standards Track PAGE 29

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityDiscontinuityTime." ::= { mplsLdpEntityStatsEntry 13 } -- -- The MPLS LDP Peer Table -- mplsLdpSessionObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 3 } mplsLdpPeerLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the most recent addition or deletion to/from the mplsLdpPeerTable/mplsLdpSessionTable." ::= { mplsLdpSessionObjects 1 } mplsLdpPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about LDP peers known by Entities in the mplsLdpEntityTable. The information in this table is based on information from the Entity-Peer interaction during session initialization but is not appropriate for the mplsLdpSessionTable, because objects in this table may or may not be used in session establishment." ::= { mplsLdpSessionObjects 2 } mplsLdpPeerEntry OBJECT-TYPE SYNTAX MplsLdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single Peer which is related to a Session. This table is augmented by the mplsLdpSessionTable." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId } ::= { mplsLdpPeerTable 1 } MplsLdpPeerEntry ::= SEQUENCE { mplsLdpPeerLdpId MplsLdpIdentifier, mplsLdpPeerLabelDistMethod MplsLabelDistributionMethod, Cucchiara, et al. Standards Track PAGE 30

RFC 3815 MPLS LDP MIB June 2004 mplsLdpPeerPathVectorLimit Integer32, mplsLdpPeerTransportAddrType InetAddressType, mplsLdpPeerTransportAddr InetAddress } mplsLdpPeerLdpId OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The LDP identifier of this LDP Peer." ::= { mplsLdpPeerEntry 1 } mplsLdpPeerLabelDistMethod OBJECT-TYPE SYNTAX MplsLabelDistributionMethod MAX-ACCESS read-only STATUS current DESCRIPTION "For any given LDP session, the method of label distribution must be specified." ::= { mplsLdpPeerEntry 2 } mplsLdpPeerPathVectorLimit OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of this object is 0 (zero) then Loop Dection for Path Vectors for this Peer is disabled. Otherwise, if this object has a value greater than zero, then Loop Dection for Path Vectors for this Peer is enabled and the Path Vector Limit is this value." REFERENCE "RFC 3036, LDP Specification, Section 2.8 Loop Dection, Section 3.4.5 Path Vector TLV." ::= { mplsLdpPeerEntry 3 } mplsLdpPeerTransportAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Internet address for the mplsLdpPeerTransportAddr object. The LDP specification describes this as being either an IPv4 Transport Address or IPv6 Transport Cucchiara, et al. Standards Track PAGE 31

RFC 3815 MPLS LDP MIB June 2004 Address which is used in opening the LDP session's TCP connection, or if the optional TLV is not present, then this is the IPv4/IPv6 source address for the UPD packet carrying the Hellos. This object specifies how the value of the mplsLdpPeerTransportAddr object should be interpreted." REFERENCE "RFC 3036, LDP Specification, Section 2.5.2 Transport Connection Establishment and Section 3.5.2.1 Hello Message Procedures." ::= { mplsLdpPeerEntry 4 } mplsLdpPeerTransportAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Internet address advertised by the peer in the Hello Message or the Hello source address. The type of this address is specified by the value of the mplsLdpPeerTransportAddrType object." REFERENCE "RFC 3036, LDP Specification, Section 2.5.2 Transport Connection Establishment and Section 3.5.2.1 Hello Message Procedures." ::= { mplsLdpPeerEntry 5 } -- -- The MPLS LDP Sessions Table -- mplsLdpSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Sessions between the LDP Entities and LDP Peers. This table AUGMENTS the mplsLdpPeerTable. Each row in this table represents a single session." ::= { mplsLdpSessionObjects 3 } mplsLdpSessionEntry OBJECT-TYPE SYNTAX MplsLdpSessionEntry Cucchiara, et al. Standards Track PAGE 32

RFC 3815 MPLS LDP MIB June 2004 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single session between an LDP Entity and LDP Peer. The information contained in a row is read-only. Please note: the Path Vector Limit for the Session is the value which is configured in the corresponding mplsLdpEntityEntry. The Peer's Path Vector Limit is in the mplsLdpPeerPathVectorLimit object in the mplsLdpPeerTable. Values which may differ from those configured are noted in the objects of this table, the mplsLdpAtmSessionTable and the mplsLdpFrameRelaySessionTable. A value will differ if it was negotiated between the Entity and the Peer. Values may or may not be negotiated. For example, if the values are the same then no negotiation takes place. If they are negotiated, then they may differ." AUGMENTS { mplsLdpPeerEntry } ::= { mplsLdpSessionTable 1 } MplsLdpSessionEntry ::= SEQUENCE { mplsLdpSessionStateLastChange TimeStamp, mplsLdpSessionState INTEGER, mplsLdpSessionRole INTEGER, mplsLdpSessionProtocolVersion Unsigned32, mplsLdpSessionKeepAliveHoldTimeRem TimeInterval, mplsLdpSessionKeepAliveTime Unsigned32, mplsLdpSessionMaxPduLength Unsigned32, mplsLdpSessionDiscontinuityTime TimeStamp } mplsLdpSessionStateLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time this Session entered its current state as denoted by the mplsLdpSessionState object." ::= { mplsLdpSessionEntry 1 } Cucchiara, et al. Standards Track PAGE 33

RFC 3815 MPLS LDP MIB June 2004 mplsLdpSessionState OBJECT-TYPE SYNTAX INTEGER { nonexistent(1), initialized(2), openrec(3), opensent(4), operational(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the session, all of the states 1 to 5 are based on the state machine for session negotiation behavior." REFERENCE "RFC 3036, LDP Specification, Section 2.5.4, Initialization State Machine." ::= { mplsLdpSessionEntry 2 } mplsLdpSessionRole OBJECT-TYPE SYNTAX INTEGER { unknown(1), active(2), passive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "During session establishment the LSR/LER takes either the active role or the passive role based on address comparisons. This object indicates whether this LSR/LER was behaving in an active role or passive role during this session's establishment. The value of unknown(1), indicates that the role is not able to be determined at the present time." REFERENCE "RFC 3036, LDP Specification, Section 2.5.3., Session Initialization" ::= { mplsLdpSessionEntry 3 } mplsLdpSessionProtocolVersion OBJECT-TYPE SYNTAX Unsigned32(1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the LDP Protocol which this session is using. This is the version of Cucchiara, et al. Standards Track PAGE 34

RFC 3815 MPLS LDP MIB June 2004 the LDP protocol which has been negotiated during session initialization." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3, Initialization Message." ::= { mplsLdpSessionEntry 4 } mplsLdpSessionKeepAliveHoldTimeRem OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "The keep alive hold time remaining for this session." ::= { mplsLdpSessionEntry 5 } mplsLdpSessionKeepAliveTime OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The negotiated KeepAlive Time which represents the amount of seconds between keep alive messages. The mplsLdpEntityKeepAliveHoldTimer related to this Session is the value that was proposed as the KeepAlive Time for this session. This value is negotiated during session initialization between the entity's proposed value (i.e., the value configured in mplsLdpEntityKeepAliveHoldTimer) and the peer's proposed KeepAlive Hold Timer value. This value is the smaller of the two proposed values." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3, Initialization Message." ::= { mplsLdpSessionEntry 6 } mplsLdpSessionMaxPduLength OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "octets" MAX-ACCESS read-only Cucchiara, et al. Standards Track PAGE 35

RFC 3815 MPLS LDP MIB June 2004 STATUS current DESCRIPTION "The value of maximum allowable length for LDP PDUs for this session. This value may have been negotiated during the Session Initialization. This object is related to the mplsLdpEntityMaxPduLength object. The mplsLdpEntityMaxPduLength object specifies the requested LDP PDU length, and this object reflects the negotiated LDP PDU length between the Entity and the Peer." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3, Initialization Message." ::= { mplsLdpSessionEntry 7 } mplsLdpSessionDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this session's counters suffered a discontinuity. The relevant counters are the specific instances associated with this session of any Counter32 object contained in the mplsLdpSessionStatsTable. The initial value of this object is the value of sysUpTime when the entry was created in this table. Also, a command generator can distinguish when a session between a given Entity and Peer goes away and a new session is established. This value would change and thus indicate to the command generator that this is a different session." ::= { mplsLdpSessionEntry 8 } -- -- The MPLS LDP Session Statistics Table -- mplsLdpSessionStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpSessionStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of statistics for Sessions between LDP Entities and LDP Peers. This table AUGMENTS Cucchiara, et al. Standards Track PAGE 36

RFC 3815 MPLS LDP MIB June 2004 the mplsLdpPeerTable." ::= { mplsLdpSessionObjects 4 } mplsLdpSessionStatsEntry OBJECT-TYPE SYNTAX MplsLdpSessionStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents statistical information on a single session between an LDP Entity and LDP Peer." AUGMENTS { mplsLdpPeerEntry } ::= { mplsLdpSessionStatsTable 1 } MplsLdpSessionStatsEntry ::= SEQUENCE { mplsLdpSessionStatsUnknownMesTypeErrors Counter32, mplsLdpSessionStatsUnknownTlvErrors Counter32 } mplsLdpSessionStatsUnknownMesTypeErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Unknown Message Type Errors detected by this LSR/LER during this session. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpSessionDiscontinuityTime." ::= { mplsLdpSessionStatsEntry 1 } mplsLdpSessionStatsUnknownTlvErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of Unknown TLV Errors detected by this LSR/LER during this session. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of mplsLdpSessionDiscontinuityTime." ::= { mplsLdpSessionStatsEntry 2 } Cucchiara, et al. Standards Track PAGE 37

RFC 3815 MPLS LDP MIB June 2004 -- -- The MPLS LDP Hello Adjacency Table -- mplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::= { mplsLdpSessionObjects 5 } mplsLdpHelloAdjacencyTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpHelloAdjacencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Hello Adjacencies for Sessions." ::= { mplsLdpHelloAdjacencyObjects 1 } mplsLdpHelloAdjacencyEntry OBJECT-TYPE SYNTAX MplsLdpHelloAdjacencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello Adjacencies." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsLdpHelloAdjacencyIndex } ::= { mplsLdpHelloAdjacencyTable 1 } MplsLdpHelloAdjacencyEntry ::= SEQUENCE { mplsLdpHelloAdjacencyIndex Unsigned32, mplsLdpHelloAdjacencyHoldTimeRem TimeInterval, mplsLdpHelloAdjacencyHoldTime Unsigned32, mplsLdpHelloAdjacencyType INTEGER } mplsLdpHelloAdjacencyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An identifier for this specific adjacency." ::= { mplsLdpHelloAdjacencyEntry 1 } mplsLdpHelloAdjacencyHoldTimeRem OBJECT-TYPE SYNTAX TimeInterval UNITS "seconds" MAX-ACCESS read-only Cucchiara, et al. Standards Track PAGE 38

RFC 3815 MPLS LDP MIB June 2004 STATUS current DESCRIPTION "If the value of this object is 65535, this means that the hold time is infinite (i.e., wait forever). Otherwise, the time remaining for this Hello Adjacency to receive its next Hello Message. This interval will change when the 'next' Hello Message which corresponds to this Hello Adjacency is received unless it is infinite." ::= { mplsLdpHelloAdjacencyEntry 2 } mplsLdpHelloAdjacencyHoldTime OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The Hello hold time which is negotiated between the Entity and the Peer. The entity associated with this Hello Adjacency issues a proposed Hello Hold Time value in the mplsLdpEntityHelloHoldTimer object. The peer also proposes a value and this object represents the negotiated value. A value of 0 means the default, which is 15 seconds for Link Hellos and 45 seconds for Targeted Hellos. A value of 65535 indicates an infinite hold time." REFERENCE "RFC 3036, LDP Specification, Section 3.5.2 Hello Message" ::= { mplsLdpHelloAdjacencyEntry 3 } mplsLdpHelloAdjacencyType OBJECT-TYPE SYNTAX INTEGER { link(1), targeted(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This adjacency is the result of a 'link' hello if the value of this object is link(1). Cucchiara, et al. Standards Track PAGE 39

RFC 3815 MPLS LDP MIB June 2004 Otherwise, it is a result of a 'targeted' hello, targeted(2)." ::= { mplsLdpHelloAdjacencyEntry 4 } -- -- Session Label (LSP) Mapping to LSR MIB's -- In Segment LIB Information. -- -- -- NOTE: the next 2 tables map to the -- MPLS-LSR-STD-MIB's MplsInSegmentTable -- and MplsOutSegmentTable. The -- cross-connect (XC) information is not -- represented here as it can be gleaned -- from the MPLS-LSR-STD-MIB. -- mplsInSegmentLdpLspTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsInSegmentLdpLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of LDP LSP's which map to the mplsInSegmentTable in the MPLS-LSR-STD-MIB module." ::= { mplsLdpSessionObjects 6 } mplsInSegmentLdpLspEntry OBJECT-TYPE SYNTAX MplsInSegmentLdpLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single LDP LSP which is represented by a session's index triple (mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the index for the mplsInSegmentTable (mplsInSegmentLdpLspLabelIndex) from the MPLS-LSR-STD-MIB. The information contained in a row is read-only." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsInSegmentLdpLspIndex } ::= { mplsInSegmentLdpLspTable 1 } Cucchiara, et al. Standards Track PAGE 40

RFC 3815 MPLS LDP MIB June 2004 MplsInSegmentLdpLspEntry ::= SEQUENCE { mplsInSegmentLdpLspIndex MplsIndexType, mplsInSegmentLdpLspLabelType MplsLdpLabelType, mplsInSegmentLdpLspType MplsLspType } mplsInSegmentLdpLspIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This contains the same value as the mplsInSegmentIndex in the MPLS-LSR-STD-MIB's mplsInSegmentTable." ::= { mplsInSegmentLdpLspEntry 1 } mplsInSegmentLdpLspLabelType OBJECT-TYPE SYNTAX MplsLdpLabelType MAX-ACCESS read-only STATUS current DESCRIPTION "The Layer 2 Label Type." ::= { mplsInSegmentLdpLspEntry 2 } mplsInSegmentLdpLspType OBJECT-TYPE SYNTAX MplsLspType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of LSP connection." ::= { mplsInSegmentLdpLspEntry 3 } -- -- Session Label (LSP) Mapping to LSR MIB's -- Out Segment LIB Information. -- mplsOutSegmentLdpLspTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsOutSegmentLdpLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of LDP LSP's which map to the mplsOutSegmentTable in the MPLS-LSR-STD-MIB." ::= { mplsLdpSessionObjects 7 } mplsOutSegmentLdpLspEntry OBJECT-TYPE Cucchiara, et al. Standards Track PAGE 41

RFC 3815 MPLS LDP MIB June 2004 SYNTAX MplsOutSegmentLdpLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single LDP LSP which is represented by a session's index triple (mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the index (mplsOutSegmentLdpLspIndex) for the mplsOutSegmentTable. The information contained in a row is read-only." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsOutSegmentLdpLspIndex } ::= { mplsOutSegmentLdpLspTable 1 } MplsOutSegmentLdpLspEntry ::= SEQUENCE { mplsOutSegmentLdpLspIndex MplsIndexType, mplsOutSegmentLdpLspLabelType MplsLdpLabelType, mplsOutSegmentLdpLspType MplsLspType } mplsOutSegmentLdpLspIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This contains the same value as the mplsOutSegmentIndex in the MPLS-LSR-STD-MIB's mplsOutSegmentTable." ::= { mplsOutSegmentLdpLspEntry 1 } mplsOutSegmentLdpLspLabelType OBJECT-TYPE SYNTAX MplsLdpLabelType MAX-ACCESS read-only STATUS current DESCRIPTION "The Layer 2 Label Type." ::= { mplsOutSegmentLdpLspEntry 2 } mplsOutSegmentLdpLspType OBJECT-TYPE SYNTAX MplsLspType MAX-ACCESS read-only STATUS current DESCRIPTION Cucchiara, et al. Standards Track PAGE 42

RFC 3815 MPLS LDP MIB June 2004 "The type of LSP connection." ::= { mplsOutSegmentLdpLspEntry 3 } -- -- Mpls FEC Table -- mplsFecObjects OBJECT IDENTIFIER ::= { mplsLdpSessionObjects 8 } mplsFecLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the most recent addition/deletion of an entry to/from the mplsLdpFectTable or the most recent change in values to any objects in the mplsLdpFecTable. If no such changes have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { mplsFecObjects 1 } mplsFecIndexNext OBJECT-TYPE SYNTAX IndexIntegerNextFree MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for mplsFecIndex when creating entries in the mplsFecTable. The value 0 indicates that no unassigned entries are available." ::= { mplsFecObjects 2 } mplsFecTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsFecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the FEC (Forwarding Equivalence Class) Information associated with an LSP." ::= { mplsFecObjects 3 } Cucchiara, et al. Standards Track PAGE 43

RFC 3815 MPLS LDP MIB June 2004 mplsFecEntry OBJECT-TYPE SYNTAX MplsFecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row represents a single FEC Element." INDEX { mplsFecIndex } ::= { mplsFecTable 1 } MplsFecEntry ::= SEQUENCE { mplsFecIndex IndexInteger, mplsFecType INTEGER, mplsFecAddrType InetAddressType, mplsFecAddr InetAddress, mplsFecAddrPrefixLength InetAddressPrefixLength, mplsFecStorageType StorageType, mplsFecRowStatus RowStatus } mplsFecIndex OBJECT-TYPE SYNTAX IndexInteger MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index which uniquely identifies this entry." ::= { mplsFecEntry 1 } mplsFecType OBJECT-TYPE SYNTAX INTEGER { prefix(1), hostAddress(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the FEC. If the value of this object is 'prefix(1)' then the FEC type described by this row is an address prefix. If the value of this object is 'hostAddress(2)' then the FEC type described by this row is a host address." REFERENCE "RFC 3036, Section 3.4.1. FEC TLV." ::= { mplsFecEntry 2 } mplsFecAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create Cucchiara, et al. Standards Track PAGE 44

RFC 3815 MPLS LDP MIB June 2004 STATUS current DESCRIPTION "The value of this object is the type of the Internet address. The value of this object, decides how the value of the mplsFecAddr object is interpreted." REFERENCE "RFC 3036, Section 3.4.1. FEC TLV." ::= { mplsFecEntry 4 } mplsFecAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object is interpreted based on the value of the 'mplsFecAddrType' object. This address is then further interpretted as an being used with the address prefix, or as the host address. This further interpretation is indicated by the 'mplsFecType' object. In other words, the FEC element is populated according to the Prefix FEC Element value encoding, or the Host Address FEC Element encoding." REFERENCE "RFC 3036, Section 3.4.1 FEC TLV." ::= { mplsFecEntry 5 } mplsFecAddrPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of the 'mplsFecType' is 'hostAddress(2)' then this object is undefined. If the value of 'mplsFecType' is 'prefix(1)' then the value of this object is the length in bits of the address prefix represented by 'mplsFecAddr', or zero. If the value of this object is zero, this indicates that the prefix matches all addresses. In this case the address prefix MUST also be zero (i.e., 'mplsFecAddr' should have the value of zero.)" REFERENCE "RFC 3036, Section 3.4.1. FEC TLV." DEFVAL { 0 } Cucchiara, et al. Standards Track PAGE 45

RFC 3815 MPLS LDP MIB June 2004 ::= { mplsFecEntry 3 } mplsFecStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsFecEntry 6 } mplsFecRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. If the value of this object is 'active(1)', then none of the writable objects of this entry can be modified, except to set this object to 'destroy(6)'. NOTE: if this row is being referenced by any entry in the mplsLdpLspFecTable, then a request to destroy this row, will result in an inconsistentValue error." ::= { mplsFecEntry 7 } -- -- LDP LSP FEC Table -- mplsLdpLspFecLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the most recent addition/deletion of an entry to/from the mplsLdpLspFecTable or the most recent change in values to any objects in the mplsLdpLspFecTable. If no such changes have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { mplsLdpSessionObjects 9 } Cucchiara, et al. Standards Track PAGE 46

RFC 3815 MPLS LDP MIB June 2004 mplsLdpLspFecTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpLspFecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table which shows the relationship between LDP LSPs and FECs. Each row represents a single LDP LSP to FEC association." ::= { mplsLdpSessionObjects 10 } mplsLdpLspFecEntry OBJECT-TYPE SYNTAX MplsLdpLspFecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry represents a LDP LSP to FEC association." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsLdpLspFecSegment, mplsLdpLspFecSegmentIndex, mplsLdpLspFecIndex } ::= { mplsLdpLspFecTable 1 } MplsLdpLspFecEntry ::= SEQUENCE { mplsLdpLspFecSegment INTEGER, mplsLdpLspFecSegmentIndex MplsIndexType, mplsLdpLspFecIndex IndexInteger, mplsLdpLspFecStorageType StorageType, mplsLdpLspFecRowStatus RowStatus } mplsLdpLspFecSegment OBJECT-TYPE SYNTAX INTEGER { inSegment(1), outSegment(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value is inSegment(1), then this indicates that the following index, mplsLdpLspFecSegmentIndex, contains the same value as the mplsInSegmentLdpLspIndex. Otherwise, if the value of this object is Cucchiara, et al. Standards Track PAGE 47

RFC 3815 MPLS LDP MIB June 2004 outSegment(2), then this indicates that following index, mplsLdpLspFecSegmentIndex, contains the same value as the mplsOutSegmentLdpLspIndex." ::= { mplsLdpLspFecEntry 1 } mplsLdpLspFecSegmentIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index is interpretted by using the value of the mplsLdpLspFecSegment. If the mplsLdpLspFecSegment is inSegment(1), then this index has the same value as mplsInSegmentLdpLspIndex. If the mplsLdpLspFecSegment is outSegment(2), then this index has the same value as mplsOutSegmentLdpLspIndex." ::= { mplsLdpLspFecEntry 2 } mplsLdpLspFecIndex OBJECT-TYPE SYNTAX IndexInteger MAX-ACCESS not-accessible STATUS current DESCRIPTION "This index identifies the FEC entry in the mplsFecTable associated with this session. In other words, the value of this index is the same as the value of the mplsFecIndex that denotes the FEC associated with this Session." ::= { mplsLdpLspFecEntry 3 } mplsLdpLspFecStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsLdpLspFecEntry 4 } Cucchiara, et al. Standards Track PAGE 48

RFC 3815 MPLS LDP MIB June 2004 mplsLdpLspFecRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. If the value of this object is 'active(1)', then none of the writable objects of this entry can be modified. The Agent should delete this row when the session ceases to exist. If an operator wants to associate the session with a different FEC, the recommended procedure is (as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object) is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. This will also cause this entry to be deleted. Then, set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated. Once the session is initiated, an entry may be added to this table to associate the new session with a FEC." ::= { mplsLdpLspFecEntry 5 } -- -- Address Message/Address Withdraw Message Information -- -- This information is associated with a specific Session -- because Label Address Messages are sent after session -- initialization has taken place. -- mplsLdpSessionPeerAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpSessionPeerAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table 'extends' the mplsLdpSessionTable. This table is used to store Label Address Information from Label Address Messages received by this LSR from Peers. This table is read-only and should be updated Cucchiara, et al. Standards Track PAGE 49

RFC 3815 MPLS LDP MIB June 2004 when Label Withdraw Address Messages are received, i.e., Rows should be deleted as appropriate. NOTE: since more than one address may be contained in a Label Address Message, this table 'sparse augments', the mplsLdpSessionTable's information." ::= { mplsLdpSessionObjects 11 } mplsLdpSessionPeerAddrEntry OBJECT-TYPE SYNTAX MplsLdpSessionPeerAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a session's single next hop address which was advertised in an Address Message from the LDP peer. The information contained in a row is read-only." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsLdpSessionPeerAddrIndex } ::= { mplsLdpSessionPeerAddrTable 1 } MplsLdpSessionPeerAddrEntry ::= SEQUENCE { mplsLdpSessionPeerAddrIndex Unsigned32, mplsLdpSessionPeerNextHopAddrType InetAddressType, mplsLdpSessionPeerNextHopAddr InetAddress } mplsLdpSessionPeerAddrIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index which uniquely identifies this entry within a given session." ::= { mplsLdpSessionPeerAddrEntry 1 } mplsLdpSessionPeerNextHopAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The internetwork layer address type of this Next Hop Address as specified in the Label Address Message associated with this Session. The value of this object indicates how to interpret the value of Cucchiara, et al. Standards Track PAGE 50

RFC 3815 MPLS LDP MIB June 2004 mplsLdpSessionPeerNextHopAddr." ::= { mplsLdpSessionPeerAddrEntry 2 } mplsLdpSessionPeerNextHopAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next hop address. The type of this address is specified by the value of the mplsLdpSessionPeerNextHopAddrType." REFERENCE "RFC 3036, Section 2.7. LDP Identifiers and Next Hop Addresses" ::= { mplsLdpSessionPeerAddrEntry 3 } --- --- Notifications --- mplsLdpInitSessionThresholdExceeded NOTIFICATION-TYPE OBJECTS { mplsLdpEntityInitSessionThreshold } STATUS current DESCRIPTION "This notification is generated when the value of the 'mplsLdpEntityInitSessionThreshold' object is not zero, and the number of Session Initialization messages exceeds the value of the 'mplsLdpEntityInitSessionThreshold' object." ::= { mplsLdpNotifications 1 } mplsLdpPathVectorLimitMismatch NOTIFICATION-TYPE OBJECTS { mplsLdpEntityPathVectorLimit, mplsLdpPeerPathVectorLimit } STATUS current DESCRIPTION "This notification is sent when the 'mplsLdpEntityPathVectorLimit' does NOT match the value of the 'mplsLdpPeerPathVectorLimit' for a specific Entity." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3." ::= { mplsLdpNotifications 2 } Cucchiara, et al. Standards Track PAGE 51

RFC 3815 MPLS LDP MIB June 2004 mplsLdpSessionUp NOTIFICATION-TYPE OBJECTS { mplsLdpSessionState, mplsLdpSessionDiscontinuityTime, mplsLdpSessionStatsUnknownMesTypeErrors, mplsLdpSessionStatsUnknownTlvErrors } STATUS current DESCRIPTION "If this notification is sent when the value of 'mplsLdpSessionState' enters the 'operational(5)' state." ::= { mplsLdpNotifications 3 } mplsLdpSessionDown NOTIFICATION-TYPE OBJECTS { mplsLdpSessionState, mplsLdpSessionDiscontinuityTime, mplsLdpSessionStatsUnknownMesTypeErrors, mplsLdpSessionStatsUnknownTlvErrors } STATUS current DESCRIPTION "This notification is sent when the value of 'mplsLdpSessionState' leaves the 'operational(5)' state." ::= { mplsLdpNotifications 4 } --**************************************************************** -- Module Conformance Statement --**************************************************************** mplsLdpGroups OBJECT IDENTIFIER ::= { mplsLdpConformance 1 } mplsLdpCompliances OBJECT IDENTIFIER ::= { mplsLdpConformance 2 } -- -- Full Compliance -- mplsLdpModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-create and read-write. In other Cucchiara, et al. Standards Track PAGE 52

RFC 3815 MPLS LDP MIB June 2004 words, both monitoring and configuration are available when using this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpGeneralGroup, mplsLdpNotificationsGroup } GROUP mplsLdpLspGroup DESCRIPTION "This group must be supported if the LSR MIB is implemented, specifically the mplsInSegmentTable, the mplsOutSegmentTable or the mplsXCTable." OBJECT mplsLdpEntityTargetPeerAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpEntityTargetPeerAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpEntityRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." OBJECT mplsFecAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsFecAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT mplsFecRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION Cucchiara, et al. Standards Track PAGE 53

RFC 3815 MPLS LDP MIB June 2004 "Support for createAndWait and notInService is not required." OBJECT mplsLdpLspFecRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." OBJECT mplsLdpSessionPeerNextHopAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpSessionPeerNextHopAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." ::= { mplsLdpCompliances 1 } -- -- Read-Only Compliance -- mplsLdpModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpGeneralGroup, mplsLdpNotificationsGroup } GROUP mplsLdpLspGroup DESCRIPTION "This group must be supported if the LSR MIB is implemented, specifically the mplsInSegmentTable, the mplsOutSegmentTable or the mplsXCTable." OBJECT mplsLdpEntityProtocolVersion MIN-ACCESS read-only Cucchiara, et al. Standards Track PAGE 54

RFC 3815 MPLS LDP MIB June 2004 DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityTcpPort MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityUdpDscPort MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityMaxPduLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityKeepAliveHoldTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityHelloHoldTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityInitSessionThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityLabelDistMethod MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityLabelRetentionMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." Cucchiara, et al. Standards Track PAGE 55

RFC 3815 MPLS LDP MIB June 2004 OBJECT mplsLdpEntityPathVectorLimit MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityHopCountLimit MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityTransportAddrKind MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityTargetPeer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityTargetPeerAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpEntityTargetPeerAddr SYNTAX InetAddress (SIZE(0|4|16)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpEntityLabelType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityRowStatus SYNTAX RowStatus { active(1) } Cucchiara, et al. Standards Track PAGE 56

RFC 3815 MPLS LDP MIB June 2004 MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT mplsFecType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsFecAddrPrefixLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsFecAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsFecAddr SYNTAX InetAddress (SIZE(0|4|16)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT mplsFecStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsFecRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT mplsLdpLspFecStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." Cucchiara, et al. Standards Track PAGE 57

RFC 3815 MPLS LDP MIB June 2004 OBJECT mplsLdpLspFecRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT mplsLdpSessionPeerNextHopAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation is only required to support 'unknown(0)', IPv4 and globally unique IPv6 addresses." OBJECT mplsLdpSessionPeerNextHopAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support IPv4 and globally unique IPv6 addresses." ::= { mplsLdpCompliances 2 } -- units of conformance mplsLdpGeneralGroup OBJECT-GROUP OBJECTS { mplsLdpLsrId, mplsLdpLsrLoopDetectionCapable, mplsLdpEntityLastChange, mplsLdpEntityIndexNext, mplsLdpEntityProtocolVersion, mplsLdpEntityAdminStatus, mplsLdpEntityOperStatus, mplsLdpEntityTcpPort, mplsLdpEntityUdpDscPort, mplsLdpEntityMaxPduLength, mplsLdpEntityKeepAliveHoldTimer, mplsLdpEntityHelloHoldTimer, mplsLdpEntityInitSessionThreshold, mplsLdpEntityLabelDistMethod, mplsLdpEntityLabelRetentionMode, mplsLdpEntityPathVectorLimit, mplsLdpEntityHopCountLimit, mplsLdpEntityTransportAddrKind, mplsLdpEntityTargetPeer, mplsLdpEntityTargetPeerAddrType, mplsLdpEntityTargetPeerAddr, mplsLdpEntityLabelType, Cucchiara, et al. Standards Track PAGE 58

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityDiscontinuityTime, mplsLdpEntityStorageType, mplsLdpEntityRowStatus, mplsLdpEntityStatsSessionAttempts, mplsLdpEntityStatsSessionRejectedNoHelloErrors, mplsLdpEntityStatsSessionRejectedAdErrors, mplsLdpEntityStatsSessionRejectedMaxPduErrors, mplsLdpEntityStatsSessionRejectedLRErrors, mplsLdpEntityStatsBadLdpIdentifierErrors, mplsLdpEntityStatsBadPduLengthErrors, mplsLdpEntityStatsBadMessageLengthErrors, mplsLdpEntityStatsBadTlvLengthErrors, mplsLdpEntityStatsMalformedTlvValueErrors, mplsLdpEntityStatsKeepAliveTimerExpErrors, mplsLdpEntityStatsShutdownReceivedNotifications, mplsLdpEntityStatsShutdownSentNotifications, mplsLdpPeerLastChange, mplsLdpPeerLabelDistMethod, mplsLdpPeerPathVectorLimit, mplsLdpPeerTransportAddrType, mplsLdpPeerTransportAddr, mplsLdpHelloAdjacencyHoldTimeRem, mplsLdpHelloAdjacencyHoldTime, mplsLdpHelloAdjacencyType, mplsLdpSessionStateLastChange, mplsLdpSessionState, mplsLdpSessionRole, mplsLdpSessionProtocolVersion, mplsLdpSessionKeepAliveHoldTimeRem, mplsLdpSessionKeepAliveTime, mplsLdpSessionMaxPduLength, mplsLdpSessionDiscontinuityTime, mplsLdpSessionStatsUnknownMesTypeErrors, mplsLdpSessionStatsUnknownTlvErrors, mplsLdpSessionPeerNextHopAddrType, mplsLdpSessionPeerNextHopAddr, mplsFecLastChange, mplsFecIndexNext, mplsFecType, mplsFecAddrType, mplsFecAddr, mplsFecAddrPrefixLength, mplsFecStorageType, mplsFecRowStatus } STATUS current DESCRIPTION "Objects that apply to all MPLS LDP implementations." Cucchiara, et al. Standards Track PAGE 59

RFC 3815 MPLS LDP MIB June 2004 ::= { mplsLdpGroups 1 } mplsLdpLspGroup OBJECT-GROUP OBJECTS { mplsInSegmentLdpLspLabelType, mplsInSegmentLdpLspType, mplsOutSegmentLdpLspLabelType, mplsOutSegmentLdpLspType, mplsLdpLspFecLastChange, mplsLdpLspFecStorageType, mplsLdpLspFecRowStatus } STATUS current DESCRIPTION "These objects are for LDP implementations which interface to the Label Information Base (LIB) in the MPLS-LSR-STD-MIB. The LIB is represented in the mplsInSegmentTable, mplsOutSegmentTable and mplsXCTable." ::= { mplsLdpGroups 2 } mplsLdpNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { mplsLdpInitSessionThresholdExceeded, mplsLdpPathVectorLimitMismatch, mplsLdpSessionUp, mplsLdpSessionDown } STATUS current DESCRIPTION "The notification for an MPLS LDP implementation." ::= { mplsLdpGroups 3 } END 4.1. The MPLS-LDP-ATM-STD-MIB Module This MIB Module MUST be supported if LDP uses ATM as the Layer 2 medium. There are three tables in this MIB Module. Two tables are for configuring LDP to use ATM. These tables are the mplsLdpEntityAtmTable and the mplsLdpEntityAtmLRTable. The third table is the mplsLdpAtmSessionTable which is a read-only table. This MIB Module IMPORTS the AtmVpIdentifier TEXTUAL-CONVENTION from [RFC 2514]. Cucchiara, et al. Standards Track PAGE 60

RFC 3815 MPLS LDP MIB June 2004 4.1.1. The LDP Entity ATM Table The mplsLdpEntityAtmTable provides a way to configure information which would be contained in the "Optional Parameter" portion of an LDP PDU Initialization Message. 4.1.2. The LDP Entity ATM Label Range Table The mplsLdpEntityAtmLRTable provides a way to configure information which would be contained in the "ATM Label Range Components" portion of an LDP PDU Intialization Message, see [RFC 3035] and [RFC 3036]. 4.1.3. The LDP ATM Session Table The MPLS LDP ATM Session Table is a read-only table which contains session information specific to ATM. MPLS-LDP-ATM-STD-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, Unsigned32 FROM SNMPv2-SMI -- [RFC 2578] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC 2580] RowStatus, StorageType FROM SNMPv2-TC -- [RFC 2579] InterfaceIndexOrZero FROM IF-MIB -- [RFC 2020] AtmVpIdentifier FROM ATM-TC-MIB -- [RFC 2514] mplsStdMIB, MplsAtmVcIdentifier FROM MPLS-TC-STD-MIB -- [RFC 3811] mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId FROM MPLS-LDP-STD-MIB -- [RFC 3813] ; mplsLdpAtmStdMIB MODULE-IDENTITY LAST-UPDATED "200406030000Z" -- June 3, 2004 Cucchiara, et al. Standards Track PAGE 61

RFC 3815 MPLS LDP MIB June 2004 ORGANIZATION "Multiprotocol Label Switching (mpls) Working Group" CONTACT-INFO "Joan Cucchiara (jcucchiara@mindspring.com) Marconi Communications, Inc. Hans Sjostrand (hans@ipunplugged.com) ipUnplugged James V. Luciani (james_luciani@mindspring.com) Marconi Communications, Inc. Working Group Chairs: George Swallow, email: swallow@cisco.com Loa Andersson, email: loa@pi.se MPLS Working Group, email: mpls@uu.net " DESCRIPTION "Copyright © The Internet Society (2004). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for configuring and monitoring the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP), utilizing Asynchronous Transfer Mode (ATM) as the Layer 2 media." REVISION "200406030000Z" -- June 3, 2004 DESCRIPTION "Initial version published as part of RFC 3815." ::= { mplsStdMIB 5 } --**************************************************************** mplsLdpAtmObjects OBJECT IDENTIFIER ::= { mplsLdpAtmStdMIB 1 } mplsLdpAtmConformance OBJECT IDENTIFIER ::= { mplsLdpAtmStdMIB 2 } --**************************************************************** -- MPLS LDP ATM Objects --**************************************************************** -- -- Ldp Entity Objects for ATM Cucchiara, et al. Standards Track PAGE 62

RFC 3815 MPLS LDP MIB June 2004 -- mplsLdpEntityAtmObjects OBJECT IDENTIFIER ::= { mplsLdpAtmObjects 1 } mplsLdpEntityAtmTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityAtmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ATM specific information which could be used in the 'Optional Parameters' and other ATM specific information. This table 'sparse augments' the mplsLdpEntityTable when ATM is the Layer 2 medium." ::= { mplsLdpEntityAtmObjects 1 } mplsLdpEntityAtmEntry OBJECT-TYPE SYNTAX MplsLdpEntityAtmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the ATM parameters and ATM information for this LDP entity." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex } ::= { mplsLdpEntityAtmTable 1 } MplsLdpEntityAtmEntry ::= SEQUENCE { mplsLdpEntityAtmIfIndexOrZero InterfaceIndexOrZero, mplsLdpEntityAtmMergeCap INTEGER, mplsLdpEntityAtmLRComponents Unsigned32, mplsLdpEntityAtmVcDirectionality INTEGER, mplsLdpEntityAtmLsrConnectivity INTEGER, mplsLdpEntityAtmDefaultControlVpi AtmVpIdentifier, mplsLdpEntityAtmDefaultControlVci MplsAtmVcIdentifier, mplsLdpEntityAtmUnlabTrafVpi AtmVpIdentifier, mplsLdpEntityAtmUnlabTrafVci MplsAtmVcIdentifier, mplsLdpEntityAtmStorageType StorageType, mplsLdpEntityAtmRowStatus RowStatus } mplsLdpEntityAtmIfIndexOrZero OBJECT-TYPE SYNTAX InterfaceIndexOrZero Cucchiara, et al. Standards Track PAGE 63

RFC 3815 MPLS LDP MIB June 2004 MAX-ACCESS read-create STATUS current DESCRIPTION "This value represents either the InterfaceIndex or 0 (zero). The value of zero means that the InterfaceIndex is not known. However, if the InterfaceIndex is known, then it must be represented by this value. If an InterfaceIndex becomes known, then the network management entity (e.g., SNMP agent) responsible for this object MUST change the value from 0 (zero) to the value of the InterfaceIndex. If an ATM Label is being used in forwarding data, then the value of this object MUST be the InterfaceIndex." ::= { mplsLdpEntityAtmEntry 1 } mplsLdpEntityAtmMergeCap OBJECT-TYPE SYNTAX INTEGER { notSupported(0), vpMerge(1), vcMerge(2), vpAndVcMerge(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes the Merge Capability of this Entity. This is the EXACT value for the ATM Session Parameter, field M (for ATM Merge Capabilities). The ATM Session Parameter is an optional parameter in the Initialization Message. The description from RFC 3036.txt is: 'M, ATM Merge Capabilities Specifies the merge capabilities of an ATM switch. The following values are supported in this version of the specification: Value Meaning 0 Merge not supported 1 VP Merge supported 2 VC Merge supported 3 VP & VC Merge supported Cucchiara, et al. Standards Track PAGE 64

RFC 3815 MPLS LDP MIB June 2004 If the merge capabilities of the LSRs differ, then: - Non-merge and VC-merge LSRs may freely interoperate. - The interoperability of VP-merge-capable switches with non-VP-merge-capable switches is a subject for future study. When the LSRs differ on the use of VP-merge, the session is established, but VP merge is not used.' Please refer to the following reference for a complete description of this feature." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3 Initialization Message." ::= { mplsLdpEntityAtmEntry 2 } mplsLdpEntityAtmLRComponents OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Label Range Components in the Initialization message. This also represents the number of entries in the mplsLdpEntityAtmLRTable which correspond to this entry. This is the EXACT value for the ATM Session Parameter, field N (for Number of label range components). The ATM Session Parameter is an optional parameter in the Initialization Message. The description from RFC 3036.txt is: 'N, Number of label range components Specifies the number of ATM Label Range Components included in the TLV.' Please refer to the following reference for a complete description of this feature." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3 Initialization Message." ::= { mplsLdpEntityAtmEntry 3 } mplsLdpEntityAtmVcDirectionality OBJECT-TYPE SYNTAX INTEGER { bidirectional(0), Cucchiara, et al. Standards Track PAGE 65

RFC 3815 MPLS LDP MIB June 2004 unidirectional(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of this object is 'bidirectional(0)', a given VCI, within a given VPI, is used as a label for both directions independently. If the value of this object is 'unidirectional(1)', a given VCI within a VPI designates one direction. This is the EXACT value for the ATM Session Parameter, field D (for VC Directionality). The ATM Session Parameter is an optional parameter in the Initialization Message. The description from RFC 3036.txt is: 'D, VC Directionality A value of 0 specifies bidirectional VC capability, meaning the LSR can (within a given VPI) support the use of a given VCI as a label for both link directions independently. A value of 1 specifies unidirectional VC capability, meaning (within a given VPI) a given VCI may appear in a label mapping for one direction on the link only. When either or both of the peers specifies unidirectional VC capability, both LSRs use unidirectional VC label assignment for the link as follows. The LSRs compare their LDP Identifiers as unsigned integers. The LSR with the larger LDP Identifier may assign only odd-numbered VCIs in the VPI/VCI range as labels. The system with the smaller LDP Identifier may assign only even-numbered VCIs in the VPI/VCI range as labels.' Please refer to the following reference for a complete description of this feature." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3 Initialization Message." ::= { mplsLdpEntityAtmEntry 4 } mplsLdpEntityAtmLsrConnectivity OBJECT-TYPE SYNTAX INTEGER { direct(1), Cucchiara, et al. Standards Track PAGE 66

RFC 3815 MPLS LDP MIB June 2004 indirect(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The peer LSR may be connected indirectly by means of an ATM VP so that the VPI values may be different on either endpoint so the label MUST be encoded entirely within the VCI field." DEFVAL { direct } ::= { mplsLdpEntityAtmEntry 5 } mplsLdpEntityAtmDefaultControlVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The default VPI value for the non-MPLS connection. The default value of this is 0 (zero) but other values may be configured. This object allows a different value to be configured." DEFVAL { 0 } ::= { mplsLdpEntityAtmEntry 6 } mplsLdpEntityAtmDefaultControlVci OBJECT-TYPE SYNTAX MplsAtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The Default VCI value for a non-MPLS connection. The default value of this is 32 but other values may be configured. This object allows a different value to be configured." DEFVAL { 32 } ::= { mplsLdpEntityAtmEntry 7 } mplsLdpEntityAtmUnlabTrafVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "VPI value of the VCC supporting unlabeled traffic. This non-MPLS connection is used to carry unlabeled (IP) packets. The default value is the same as the default value of the 'mplsLdpEntityAtmDefaultControlVpi', however another value may be configured." DEFVAL { 0 } ::= { mplsLdpEntityAtmEntry 8 } Cucchiara, et al. Standards Track PAGE 67

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityAtmUnlabTrafVci OBJECT-TYPE SYNTAX MplsAtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "VCI value of the VCC supporting unlabeled traffic. This non-MPLS connection is used to carry unlabeled (IP) packets. The default value is the same as the default value of the 'mplsLdpEntityAtmDefaultControlVci', however another value may be configured." DEFVAL { 32 } ::= { mplsLdpEntityAtmEntry 9 } mplsLdpEntityAtmStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsLdpEntityAtmEntry 10 } mplsLdpEntityAtmRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated." ::= { mplsLdpEntityAtmEntry 11 } -- Cucchiara, et al. Standards Track PAGE 68

RFC 3815 MPLS LDP MIB June 2004 -- The MPLS LDP Entity ATM Label Range Table -- mplsLdpEntityAtmLRTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityAtmLREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS LDP Entity ATM Label Range (LR) Table. The purpose of this table is to provide a mechanism for configuring a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Entities. LDP Entities which use ATM must have at least one entry in this table. There must exist at least one entry in this table for every LDP Entity that has 'mplsLdpEntityOptionalParameters' object with a value of 'atmSessionParameters'." ::= { mplsLdpEntityAtmObjects 2 } mplsLdpEntityAtmLREntry OBJECT-TYPE SYNTAX MplsLdpEntityAtmLREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LDP Entity ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. These are the same data used in the Initialization Message. NOTE: The ranges for a specific LDP Entity are UNIQUE and non-overlapping. For example, for a specific LDP Entity index, there could be one entry having LowerBound vpi/vci == 0/32, and UpperBound vpi/vci == 0/100, and a second entry for this same interface with LowerBound vpi/vci == 0/101 and UpperBound vpi/vci == 0/200. However, there could not be a third entry with LowerBound vpi/vci == 0/200 and UpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e., both entries now have 0/200). Cucchiara, et al. Standards Track PAGE 69

RFC 3815 MPLS LDP MIB June 2004 A row will not become active unless a unique and non-overlapping range is specified. At least one label range entry for a specific LDP Entity MUST include the default VPI/VCI values denoted in the LDP Entity Table. A request to create a row with an overlapping range should result in an inconsistentValue error." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpEntityAtmLRMinVpi, mplsLdpEntityAtmLRMinVci } ::= { mplsLdpEntityAtmLRTable 1 } MplsLdpEntityAtmLREntry ::= SEQUENCE { mplsLdpEntityAtmLRMinVpi AtmVpIdentifier, mplsLdpEntityAtmLRMinVci MplsAtmVcIdentifier, mplsLdpEntityAtmLRMaxVpi AtmVpIdentifier, mplsLdpEntityAtmLRMaxVci MplsAtmVcIdentifier, mplsLdpEntityAtmLRStorageType StorageType, mplsLdpEntityAtmLRRowStatus RowStatus } mplsLdpEntityAtmLRMinVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum VPI number configured for this range. The value of zero is a valid value for the VPI portion of the label." ::= { mplsLdpEntityAtmLREntry 1 } mplsLdpEntityAtmLRMinVci OBJECT-TYPE SYNTAX MplsAtmVcIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum VCI number configured for this range." ::= { mplsLdpEntityAtmLREntry 2 } mplsLdpEntityAtmLRMaxVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create Cucchiara, et al. Standards Track PAGE 70

RFC 3815 MPLS LDP MIB June 2004 STATUS current DESCRIPTION "The maximum VPI number configured for this range." ::= { mplsLdpEntityAtmLREntry 3 } mplsLdpEntityAtmLRMaxVci OBJECT-TYPE SYNTAX MplsAtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum VCI number configured for this range." ::= { mplsLdpEntityAtmLREntry 4 } mplsLdpEntityAtmLRStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsLdpEntityAtmLREntry 5 } mplsLdpEntityAtmLRRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated." ::= { mplsLdpEntityAtmLREntry 6 } Cucchiara, et al. Standards Track PAGE 71

RFC 3815 MPLS LDP MIB June 2004 -- -- MPLS LDP ATM Session Information -- mplsLdpAtmSessionObjects OBJECT IDENTIFIER ::= { mplsLdpAtmObjects 2 } mplsLdpAtmSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpAtmSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table which relates sessions in the 'mplsLdpSessionTable' and their label range intersections. There could be one or more label range intersections between an LDP Entity and LDP Peer using ATM as the underlying media. Each row represents a single label range intersection. This table cannot use the 'AUGMENTS' clause because there is not necessarily a one-to-one mapping between this table and the mplsLdpSessionTable." ::= { mplsLdpAtmSessionObjects 1 } mplsLdpAtmSessionEntry OBJECT-TYPE SYNTAX MplsLdpAtmSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single label range intersection between an LDP Entity and LDP Peer. The information contained in a row is read-only." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsLdpSessionAtmLRLowerBoundVpi, mplsLdpSessionAtmLRLowerBoundVci } ::= { mplsLdpAtmSessionTable 1 } MplsLdpAtmSessionEntry ::= SEQUENCE { mplsLdpSessionAtmLRLowerBoundVpi AtmVpIdentifier, mplsLdpSessionAtmLRLowerBoundVci MplsAtmVcIdentifier, mplsLdpSessionAtmLRUpperBoundVpi AtmVpIdentifier, Cucchiara, et al. Standards Track PAGE 72

RFC 3815 MPLS LDP MIB June 2004 mplsLdpSessionAtmLRUpperBoundVci MplsAtmVcIdentifier } mplsLdpSessionAtmLRLowerBoundVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum VPI number for this range." ::= { mplsLdpAtmSessionEntry 1 } mplsLdpSessionAtmLRLowerBoundVci OBJECT-TYPE SYNTAX MplsAtmVcIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum VCI number for this range." ::= { mplsLdpAtmSessionEntry 2 } mplsLdpSessionAtmLRUpperBoundVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum VPI number for this range." ::= { mplsLdpAtmSessionEntry 3 } mplsLdpSessionAtmLRUpperBoundVci OBJECT-TYPE SYNTAX MplsAtmVcIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum VCI number for this range." ::= { mplsLdpAtmSessionEntry 4 } --************************************************************** -- Module Conformance Statement --************************************************************** mplsLdpAtmGroups OBJECT IDENTIFIER ::= { mplsLdpAtmConformance 1 } mplsLdpAtmCompliances OBJECT IDENTIFIER ::= { mplsLdpAtmConformance 2 } -- -- Full Compliance -- Cucchiara, et al. Standards Track PAGE 73

RFC 3815 MPLS LDP MIB June 2004 mplsLdpAtmModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpAtmGroup } OBJECT mplsLdpEntityAtmRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." OBJECT mplsLdpEntityAtmLRRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." ::= { mplsLdpAtmCompliances 1 } -- -- Read-Only Compliance -- mplsLdpAtmModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpAtmGroup } OBJECT mplsLdpEntityAtmIfIndexOrZero MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmMergeCap Cucchiara, et al. Standards Track PAGE 74

RFC 3815 MPLS LDP MIB June 2004 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmVcDirectionality MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmLsrConnectivity MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmDefaultControlVpi MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmDefaultControlVci MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmUnlabTrafVpi MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmUnlabTrafVci MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT mplsLdpEntityAtmLRMaxVpi MIN-ACCESS read-only Cucchiara, et al. Standards Track PAGE 75

RFC 3815 MPLS LDP MIB June 2004 DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmLRMaxVci MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmLRStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityAtmLRRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." ::= { mplsLdpAtmCompliances 2 } -- -- units of conformance -- mplsLdpAtmGroup OBJECT-GROUP OBJECTS { mplsLdpEntityAtmIfIndexOrZero, mplsLdpEntityAtmMergeCap, mplsLdpEntityAtmLRComponents, mplsLdpEntityAtmVcDirectionality, mplsLdpEntityAtmLsrConnectivity, mplsLdpEntityAtmDefaultControlVpi, mplsLdpEntityAtmDefaultControlVci, mplsLdpEntityAtmUnlabTrafVpi, mplsLdpEntityAtmUnlabTrafVci, mplsLdpEntityAtmStorageType, mplsLdpEntityAtmRowStatus, mplsLdpEntityAtmLRMaxVpi, mplsLdpEntityAtmLRMaxVci, mplsLdpEntityAtmLRStorageType, mplsLdpEntityAtmLRRowStatus, mplsLdpSessionAtmLRUpperBoundVpi, mplsLdpSessionAtmLRUpperBoundVci } STATUS current Cucchiara, et al. Standards Track PAGE 76

RFC 3815 MPLS LDP MIB June 2004 DESCRIPTION "Objects that apply to all MPLS LDP implementations using ATM as the Layer 2." ::= { mplsLdpAtmGroups 1 } END 4.2. The MPLS-LDP-FRAME-RELAY-STD-MIB Module This MIB Module MUST be supported if LDP uses FRAME RELAY as the Layer 2 medium. There are three tables in this MIB Module. Two tables are to configure LDP for using Frame Relay. These tables are the mplsLdpEntityFrameRelayTable and the mplsLdpEntityFrameRelayLRTable. The third table, mplsLdpFrameRelaySessionTable, is a read-only table. This MIB Module IMPORTS the DLCI TEXTUAL-CONVENTION from [RFC 2115]. 4.2.1. The LDP Entity Frame Relay Table The mplsLdpEntityFrameRelayTable provides a way to configure information which would be contained in the "Optional Parameter" portion of an LDP PDU Initialization Message. 4.2.2. The LDP Entity Frame Relay Label Range Table The mplsLdpEntityFrameRelayLRTable provides a way to configure information which would be contained in the "Frame Relay Label Range Components" portion of an LDP PDU Intialization Message, see [RFC 3034] and [RFC 3036]. 4.2.3. The LDP Frame Relay Session Table The mplsLdpFrameRelaySessionTable is a table which contains session information specific to Frame Relay. MPLS-LDP-FRAME-RELAY-STD-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, Unsigned32 FROM SNMPv2-SMI -- [RFC 2578] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC 2580] RowStatus, StorageType Cucchiara, et al. Standards Track PAGE 77

RFC 3815 MPLS LDP MIB June 2004 FROM SNMPv2-TC -- [RFC 2579] DLCI FROM FRAME-RELAY-DTE-MIB -- [RFC 2115] InterfaceIndexOrZero FROM IF-MIB -- [RFC 2020] mplsStdMIB FROM MPLS-TC-STD-MIB -- [RFC 3811] mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId FROM MPLS-LDP-STD-MIB -- [RFC 3813] ; mplsLdpFrameRelayStdMIB MODULE-IDENTITY LAST-UPDATED "200406030000Z" -- June 3, 2004 ORGANIZATION "Multiprotocol Label Switching (mpls) Working Group" CONTACT-INFO "Joan Cucchiara (jcucchiara@mindspring.com) Marconi Communications, Inc. Hans Sjostrand (hans@ipunplugged.com) ipUnplugged James V. Luciani (james_luciani@mindspring.com) Marconi Communications, Inc. Working Group Chairs: George Swallow, email: swallow@cisco.com Loa Andersson, email: loa@pi.se MPLS Working Group, email: mpls@uu.net " DESCRIPTION "Copyright © The Internet Society (year). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for configuring and monitoring the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP), utilizing Frame Relay as the Layer 2 media." Cucchiara, et al. Standards Track PAGE 78

RFC 3815 MPLS LDP MIB June 2004 REVISION "200406030000Z" -- June 6, 2004 DESCRIPTION "Initial version published as part of RFC 3815." ::= { mplsStdMIB 6 } --**************************************************************** mplsLdpFrameRelayObjects OBJECT IDENTIFIER ::= { mplsLdpFrameRelayStdMIB 1 } mplsLdpFrameRelayConformance OBJECT IDENTIFIER ::= { mplsLdpFrameRelayStdMIB 2 } --**************************************************************** -- MPLS LDP Frame Relay Objects --**************************************************************** -- -- Ldp Entity Objects for Frame Relay -- mplsLdpEntityFrameRelayObjects OBJECT IDENTIFIER ::= { mplsLdpFrameRelayObjects 1 } mplsLdpEntityFrameRelayTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityFrameRelayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Frame Relay specific information which could be used in the 'Optional Parameters' and other Frame Relay specific information. This table 'sparse augments' the mplsLdpEntityTable when Frame Relay is the Layer 2 medium." ::= { mplsLdpEntityFrameRelayObjects 1 } mplsLdpEntityFrameRelayEntry OBJECT-TYPE SYNTAX MplsLdpEntityFrameRelayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the Frame Relay optional parameters associated with the LDP entity." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex Cucchiara, et al. Standards Track PAGE 79

RFC 3815 MPLS LDP MIB June 2004 } ::= { mplsLdpEntityFrameRelayTable 1 } MplsLdpEntityFrameRelayEntry ::= SEQUENCE { mplsLdpEntityFrameRelayIfIndexOrZero InterfaceIndexOrZero, mplsLdpEntityFrameRelayMergeCap INTEGER, mplsLdpEntityFrameRelayLRComponents Unsigned32, mplsLdpEntityFrameRelayVcDirectionality INTEGER, mplsLdpEntityFrameRelayStorageType StorageType, mplsLdpEntityFrameRelayRowStatus RowStatus } mplsLdpEntityFrameRelayIfIndexOrZero OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This value represents either the InterfaceIndex of the 'ifLayer' where the Frame Relay Labels 'owned' by this entry were created, or 0 (zero). The value of zero means that the InterfaceIndex is not known. For example, if the InterfaceIndex is created subsequent to the Frame Relay Label's creation, then it would not be known. However, if the InterfaceIndex is known, then it must be represented by this value. If an InterfaceIndex becomes known, then the network management entity (e.g., SNMP agent) responsible for this object MUST change the value from 0 (zero) to the value of the InterfaceIndex. If an Frame Relay Label is being used in forwarding data, then the value of this object MUST be the InterfaceIndex." ::= { mplsLdpEntityFrameRelayEntry 1 } mplsLdpEntityFrameRelayMergeCap OBJECT-TYPE SYNTAX INTEGER { notSupported(0), supported(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "This represents whether or not the Frame Relay merge capability is supported. This is the EXACT value for the Frame Relay Session Parameter, field M (for Frame Relay Merge Capabilities). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. Cucchiara, et al. Standards Track PAGE 80

RFC 3815 MPLS LDP MIB June 2004 The description from RFC 3036.txt is: 'M, Frame Relay Merge Capabilities Specifies the merge capabilities of a Frame Relay switch. The following values are supported in this version of the specification: Value Meaning 0 Merge not supported 1 Merge supported Non-merge and merge Frame Relay LSRs may freely interoperate.' Please refer to the following reference for a complete description of this feature." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3 Initialization Message." ::= { mplsLdpEntityFrameRelayEntry 2 } mplsLdpEntityFrameRelayLRComponents OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Label Range Components in the Initialization message. This also represents the number of entries in the mplsLdpEntityFrameRelayLRTable which correspond to this entry. This is the EXACT value for the Frame Relay Session Parameter, field N (for Number of label range components). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. The description from RFC 3036.txt is: 'N, Number of label range components Specifies the number of Frame Relay Label Range Components included in the TLV.' Please refer to the following reference for a complete description of this feature." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3 Cucchiara, et al. Standards Track PAGE 81

RFC 3815 MPLS LDP MIB June 2004 Initialization Message." ::= { mplsLdpEntityFrameRelayEntry 3 } mplsLdpEntityFrameRelayVcDirectionality OBJECT-TYPE SYNTAX INTEGER { bidirectional(0), unidirection(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of this object is 'bidirectional(0)', then the LSR supports the use of a given DLCI as a label for both directions independently. If the value of this object is 'unidirectional(1)', then the LSR uses the given DLCI as a label in only one direction. This is the EXACT value for the Frame Relay Session Parameter, field D (for VC Directionality). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. The description from RFC 3036.txt is: 'D, VC Directionality A value of 0 specifies bidirectional VC capability, meaning the LSR can support the use of a given DLCI as a label for both link directions independently. A value of 1 specifies unidirectional VC capability, meaning a given DLCI may appear in a label mapping for one direction on the link only. When either or both of the peers specifies unidirectional VC capability, both LSRs use unidirectional VC label assignment for the link as follows. The LSRs compare their LDP Identifiers as unsigned integers. The LSR with the larger LDP Identifier may assign only odd-numbered DLCIs in the range as labels. The system with the smaller LDP Identifier may assign only even-numbered DLCIs in the range as labels.' Please refer to the following reference for a complete description of this feature." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3 Initialization Message." ::= { mplsLdpEntityFrameRelayEntry 4 } Cucchiara, et al. Standards Track PAGE 82

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityFrameRelayStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsLdpEntityFrameRelayEntry 5 } mplsLdpEntityFrameRelayRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated." ::= { mplsLdpEntityFrameRelayEntry 6 } -- -- Frame Relay Label Range Components -- mplsLdpEntityFrameRelayLRTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityFrameRelayLREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the Cucchiara, et al. Standards Track PAGE 83

RFC 3815 MPLS LDP MIB June 2004 Optional Parameters for the Frame Relay Session in the LDP Initialization Message, specifically it contains information about the Frame Relay Label Range Components. If the value of the object 'mplsLdpEntityOptionalParameters' contains the value of 'frameRelaySessionParameters(3)' then there must be at least one corresponding entry in this table." ::= { mplsLdpEntityFrameRelayObjects 2 } mplsLdpEntityFrameRelayLREntry OBJECT-TYPE SYNTAX MplsLdpEntityFrameRelayLREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the Frame Relay Label Range Component associated with the LDP entity." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpEntityFrameRelayLRMinDlci } ::= { mplsLdpEntityFrameRelayLRTable 1 } MplsLdpEntityFrameRelayLREntry ::= SEQUENCE { mplsLdpEntityFrameRelayLRMinDlci DLCI, mplsLdpEntityFrameRelayLRMaxDlci DLCI, mplsLdpEntityFrameRelayLRLen INTEGER, mplsLdpEntityFrameRelayLRStorageType StorageType, mplsLdpEntityFrameRelayLRRowStatus RowStatus } mplsLdpEntityFrameRelayLRMinDlci OBJECT-TYPE SYNTAX DLCI MAX-ACCESS not-accessible STATUS current DESCRIPTION "The lower bound which is supported. This value should be the same as that in the Frame Relay Label Range Component's Minimum DLCI field. The value of zero is valid for the minimum DLCI field of the label." REFERENCE "RFC 3034, Use of Label Switching on Frame Relay Networks Specification." ::= { mplsLdpEntityFrameRelayLREntry 1 } Cucchiara, et al. Standards Track PAGE 84

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityFrameRelayLRMaxDlci OBJECT-TYPE SYNTAX DLCI MAX-ACCESS read-create STATUS current DESCRIPTION "The upper bound which is supported. This value should be the same as that in the Frame Relay Label Range Component's Maximum DLCI field." ::= { mplsLdpEntityFrameRelayLREntry 2 } mplsLdpEntityFrameRelayLRLen OBJECT-TYPE SYNTAX INTEGER { tenDlciBits(0), twentyThreeDlciBits(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the length of the DLCI bits. This is the EXACT value for the Len field of the Frame Relay Label Range Component. The description from RFC 3036.txt is: 'Len This field specifies the number of bits of the DLCI. The following values are supported: Len DLCI bits 0 10 2 23 Len values 1 and 3 are reserved.' Please refer to the following reference for a complete description of this feature." REFERENCE "RFC 3036, LDP Specification, Section 3.5.3 Initialization Message." ::= { mplsLdpEntityFrameRelayLREntry 3 } mplsLdpEntityFrameRelayLRStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION Cucchiara, et al. Standards Track PAGE 85

RFC 3815 MPLS LDP MIB June 2004 "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsLdpEntityFrameRelayLREntry 4 } mplsLdpEntityFrameRelayLRRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated." ::= { mplsLdpEntityFrameRelayLREntry 5 } -- -- MPLS LDP Frame Relay Session Information -- mplsLdpFrameRelaySessionObjects OBJECT IDENTIFIER ::= { mplsLdpFrameRelayObjects 2 } mplsLdpFrameRelaySessionTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpFrameRelaySessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Frame Relay label range intersections between the LDP Entities and LDP Peers. Each row represents a single label range intersection. NOTE: this table cannot use the 'AUGMENTS' Cucchiara, et al. Standards Track PAGE 86

RFC 3815 MPLS LDP MIB June 2004 clause because there is not necessarily a one-to-one mapping between this table and the mplsLdpSessionTable." ::= { mplsLdpFrameRelaySessionObjects 1 } mplsLdpFrameRelaySessionEntry OBJECT-TYPE SYNTAX MplsLdpFrameRelaySessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single label range intersection between an LDP Entity and LDP Peer. The information contained in a row is read-only." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpPeerLdpId, mplsLdpFrameRelaySessionMinDlci } ::= { mplsLdpFrameRelaySessionTable 1 } MplsLdpFrameRelaySessionEntry ::= SEQUENCE { mplsLdpFrameRelaySessionMinDlci DLCI, mplsLdpFrameRelaySessionMaxDlci DLCI, mplsLdpFrameRelaySessionLen INTEGER } mplsLdpFrameRelaySessionMinDlci OBJECT-TYPE SYNTAX DLCI MAX-ACCESS not-accessible STATUS current DESCRIPTION "The lower bound of DLCIs which are supported. The value of zero is a valid value for the minimum DLCI field of the label." REFERENCE "RFC 3034, Use of Label Switching on Frame Relay Networks Specification." ::= { mplsLdpFrameRelaySessionEntry 1 } mplsLdpFrameRelaySessionMaxDlci OBJECT-TYPE SYNTAX DLCI MAX-ACCESS read-only STATUS current DESCRIPTION "The upper bound of DLCIs which are supported." ::= { mplsLdpFrameRelaySessionEntry 2 } Cucchiara, et al. Standards Track PAGE 87

RFC 3815 MPLS LDP MIB June 2004 mplsLdpFrameRelaySessionLen OBJECT-TYPE SYNTAX INTEGER { tenDlciBits(0), twentyThreeDlciBits(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the DLCI bits." ::= { mplsLdpFrameRelaySessionEntry 3 } --**************************************************************** -- Module Conformance Statement --**************************************************************** mplsLdpFrameRelayGroups OBJECT IDENTIFIER ::= { mplsLdpFrameRelayConformance 1 } mplsLdpFrameRelayCompliances OBJECT IDENTIFIER ::= { mplsLdpFrameRelayConformance 2 } -- -- Full Compliance -- mplsLdpFrameRelayModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpFrameRelayGroup } OBJECT mplsLdpEntityFrameRelayRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." OBJECT mplsLdpEntityFrameRelayLRRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." Cucchiara, et al. Standards Track PAGE 88

RFC 3815 MPLS LDP MIB June 2004 ::= { mplsLdpFrameRelayCompliances 1 } -- -- Read-Only Compliance -- mplsLdpFrameRelayModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpFrameRelayGroup } OBJECT mplsLdpEntityFrameRelayIfIndexOrZero MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityFrameRelayMergeCap MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityFrameRelayVcDirectionality MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityFrameRelayStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityFrameRelayRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT mplsLdpEntityFrameRelayLRMaxDlci MIN-ACCESS read-only DESCRIPTION "Write access is not required." Cucchiara, et al. Standards Track PAGE 89

RFC 3815 MPLS LDP MIB June 2004 OBJECT mplsLdpEntityFrameRelayLRLen MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityFrameRelayLRStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityFrameRelayLRRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." ::= { mplsLdpFrameRelayCompliances 2 } -- -- units of conformance -- mplsLdpFrameRelayGroup OBJECT-GROUP OBJECTS { mplsLdpEntityFrameRelayIfIndexOrZero, mplsLdpEntityFrameRelayMergeCap, mplsLdpEntityFrameRelayLRComponents, mplsLdpEntityFrameRelayVcDirectionality, mplsLdpEntityFrameRelayStorageType, mplsLdpEntityFrameRelayRowStatus, mplsLdpEntityFrameRelayLRMaxDlci, mplsLdpEntityFrameRelayLRLen, mplsLdpEntityFrameRelayLRStorageType, mplsLdpEntityFrameRelayLRRowStatus, mplsLdpFrameRelaySessionMaxDlci, mplsLdpFrameRelaySessionLen } STATUS current DESCRIPTION "Objects that apply to all MPLS LDP implementations using Frame Relay as the Layer 2." ::= { mplsLdpFrameRelayGroups 1 } END Cucchiara, et al. Standards Track PAGE 90

RFC 3815 MPLS LDP MIB June 2004 4.3. The MPLS-LDP-GENERIC-STD-MIB Module This MIB Module MUST be supported if LDP uses a Per Platform Label Space. This MIB Module contains a Label Range (LR) table for configuring MPLS Generic Label Ranges. This table is mplsLdpEntityGenericLRTable. Although the LDP Specification does not provide a way for configuring Label Ranges for Generic Labels, the MIB does provide a way to reserve a range of generic labels because this was thought to be useful by the working group. MPLS-LDP-GENERIC-STD-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, Unsigned32 FROM SNMPv2-SMI -- [RFC 2578] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC 2580] RowStatus, StorageType FROM SNMPv2-TC -- [RFC 2579] InterfaceIndexOrZero FROM IF-MIB -- [RFC 2020] mplsStdMIB FROM MPLS-TC-STD-MIB -- [RFC 3811] mplsLdpEntityLdpId, mplsLdpEntityIndex FROM MPLS-LDP-STD-MIB -- [RFC 3813] ; mplsLdpGenericStdMIB MODULE-IDENTITY LAST-UPDATED "200406030000Z" -- June 6, 2004 ORGANIZATION "Multiprotocol Label Switching (mpls) Working Group" CONTACT-INFO "Joan Cucchiara (jcucchiara@mindspring.com) Marconi Communications, Inc. Hans Sjostrand (hans@ipunplugged.com) ipUnplugged Cucchiara, et al. Standards Track PAGE 91

RFC 3815 MPLS LDP MIB June 2004 James V. Luciani (james_luciani@mindspring.com) Marconi Communications, Inc. Working Group Chairs: George Swallow, email: swallow@cisco.com Loa Andersson, email: loa@pi.se MPLS Working Group, email: mpls@uu.net " DESCRIPTION "Copyright © The Internet Society (year). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for configuring and monitoring the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP), utilizing ethernet as the Layer 2 media." REVISION "200406030000Z" -- June 6, 2004 DESCRIPTION "Initial version published as part of RFC 3815." ::= { mplsStdMIB 7 } --**************************************************************** mplsLdpGenericObjects OBJECT IDENTIFIER ::= { mplsLdpGenericStdMIB 1 } mplsLdpGenericConformance OBJECT IDENTIFIER ::= { mplsLdpGenericStdMIB 2 } --**************************************************************** -- MPLS LDP GENERIC Objects --**************************************************************** -- -- Ldp Entity Objects for Generic Labels -- mplsLdpEntityGenericObjects OBJECT IDENTIFIER ::= { mplsLdpGenericObjects 1 } -- -- The MPLS LDP Entity Generic Label Range Table -- Cucchiara, et al. Standards Track PAGE 92

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityGenericLRTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLdpEntityGenericLREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS LDP Entity Generic Label Range (LR) Table. The purpose of this table is to provide a mechanism for configurating a contiguous range of generic labels, or a 'label range' for LDP Entities. LDP Entities which use Generic Labels must have at least one entry in this table. In other words, this table 'extends' the mpldLdpEntityTable for Generic Labels." ::= { mplsLdpEntityGenericObjects 1 } mplsLdpEntityGenericLREntry OBJECT-TYPE SYNTAX MplsLdpEntityGenericLREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LDP Entity Generic Label Range (LR) Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds pairs. NOTE: there is NO corresponding LDP message which relates to the information in this table, however, this table does provide a way for a user to 'reserve' a generic label range. NOTE: The ranges for a specific LDP Entity are UNIQUE and non-overlapping. A row will not be created unless a unique and non-overlapping range is specified." INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex, mplsLdpEntityGenericLRMin, mplsLdpEntityGenericLRMax } ::= { mplsLdpEntityGenericLRTable 1 } MplsLdpEntityGenericLREntry ::= SEQUENCE { mplsLdpEntityGenericLRMin Unsigned32, mplsLdpEntityGenericLRMax Unsigned32, mplsLdpEntityGenericLabelSpace INTEGER, Cucchiara, et al. Standards Track PAGE 93

RFC 3815 MPLS LDP MIB June 2004 mplsLdpEntityGenericIfIndexOrZero InterfaceIndexOrZero, mplsLdpEntityGenericLRStorageType StorageType, mplsLdpEntityGenericLRRowStatus RowStatus } mplsLdpEntityGenericLRMin OBJECT-TYPE SYNTAX Unsigned32(0..1048575) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum label configured for this range." ::= { mplsLdpEntityGenericLREntry 1 } mplsLdpEntityGenericLRMax OBJECT-TYPE SYNTAX Unsigned32(0..1048575) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The maximum label configured for this range." ::= { mplsLdpEntityGenericLREntry 2 } mplsLdpEntityGenericLabelSpace OBJECT-TYPE SYNTAX INTEGER { perPlatform(1), perInterface(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This value of this object is perPlatform(1), then this means that the label space type is per platform. If this object is perInterface(2), then this means that the label space type is per Interface." REFERENCE "RFC 3036, LDP Specification, Section 2.2.1, Label Spaces." DEFVAL { perPlatform } ::= { mplsLdpEntityGenericLREntry 3 } mplsLdpEntityGenericIfIndexOrZero OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This value represents either the InterfaceIndex of the 'ifLayer' where these Generic Label would be created, Cucchiara, et al. Standards Track PAGE 94

RFC 3815 MPLS LDP MIB June 2004 or 0 (zero). The value of zero means that the InterfaceIndex is not known. However, if the InterfaceIndex is known, then it must be represented by this value. If an InterfaceIndex becomes known, then the network management entity (e.g., SNMP agent) responsible for this object MUST change the value from 0 (zero) to the value of the InterfaceIndex." ::= { mplsLdpEntityGenericLREntry 4 } mplsLdpEntityGenericLRStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { mplsLdpEntityGenericLREntry 5 } mplsLdpEntityGenericLRRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated. There must exist at least one entry in this table for every LDP Entity that has a generic label configured." Cucchiara, et al. Standards Track PAGE 95

RFC 3815 MPLS LDP MIB June 2004 ::= { mplsLdpEntityGenericLREntry 6 } --**************************************************************** -- Module Conformance Statement --**************************************************************** mplsLdpGenericGroups OBJECT IDENTIFIER ::= { mplsLdpGenericConformance 1 } mplsLdpGenericCompliances OBJECT IDENTIFIER ::= { mplsLdpGenericConformance 2 } -- -- Full Compliance -- mplsLdpGenericModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { mplsLdpGenericGroup } OBJECT mplsLdpEntityGenericLRRowStatus SYNTAX RowStatus { active(1) } WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait and notInService is not required." ::= { mplsLdpGenericCompliances 1 } -- -- Read-Only Compliance -- mplsLdpGenericModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE." MODULE -- this module MANDATORY-GROUPS { Cucchiara, et al. Standards Track PAGE 96

RFC 3815 MPLS LDP MIB June 2004 mplsLdpGenericGroup } OBJECT mplsLdpEntityGenericLabelSpace MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityGenericIfIndexOrZero MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityGenericLRStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsLdpEntityGenericLRRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." ::= { mplsLdpGenericCompliances 2 } -- -- units of conformance -- mplsLdpGenericGroup OBJECT-GROUP OBJECTS { mplsLdpEntityGenericLabelSpace, mplsLdpEntityGenericIfIndexOrZero, mplsLdpEntityGenericLRStorageType, mplsLdpEntityGenericLRRowStatus } STATUS current DESCRIPTION "Objects that apply to all MPLS LDP implementations using Generic Labels as the Layer 2." ::= { mplsLdpGenericGroups 1 } END Cucchiara, et al. Standards Track PAGE 97

RFC 3815 MPLS LDP MIB June 2004 5. Acknowledgments This document is a product of the MPLS Working Group. The authors would like to thank Mike MacFadden and Adrian Farrel for their helpful comments on several reviews. Also, the authors would like to give a special acknowledgement to Bert Wijnen for his many detailed reviews. Bert's assistance and guidance is greatly appreciated. We would also like to thank Cheenu Srinivasan, Arun Viswanathan and Thomas D. Nadeau, the authors of the MPLS-LSR-STD-MIB [RFC 3813], for their assistance. Additionally, there have been other members of the working group that have been very helpful: Alan Kullberg from NetPlane Systems gave input on earlier versions of this document, and more recently, Riza Cetin of Alcatel and Neil Jerram of Data Connection who both provided MIB objects. Early versions of this document were also reviewed by colleagues at Nortel Networks and Ericsson. The authors would like to thank the following people: Leigh McLellan, Geetha Brown, Geping Chen and Charlan Zhou from Nortel Networks, and Zoltan Takacs and Bo Augustsson from Ericsson. 6. References 6.1. Normative References [RFC 2115] Brown, C. and F. Baker, "Management Information Base for Frame Relay DTEs Using SMIv2", RFC 2115, September 1997. [RFC 2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC 2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP: 26, RFC 2434, October 1998. [RFC 2514] Noto, M., Spiegel, E., and K. Tesink, editors, "Definition of Textual Conventions and OBJECT-IDENTITIES for ATM Management", RFC 2514, February 1999. [RFC 2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. Cucchiara, et al. Standards Track PAGE 98

RFC 3815 MPLS LDP MIB June 2004 [RFC 2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC 2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC 2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [RFC 3031] Rosen, E., Viswananthan, A., and R. Callon, "Multiprotocol Label Switching Architecture", RFC 3031, January 2001. [RFC 3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack Encoding", RFC 3032, January 2001. [RFC 3034] Conta, A., Doolan, P., and A. Malis, "Use of Label Switching on Frame Relay Networks Specification", RFC 3034, January 2001. [RFC 3035] Davie, B., Lawrence, J., McCloghrie, K., Rosen, E., Swallow, G., Rekhter, Y., and P. Doolan, "MPLS using LDP and ATM VC Switching", RFC 3035, January 2001. [RFC 3036] Andersson, L., Doolan, P., Feldman, N., Fredette, A., and B. Thomas, "LDP Specification", RFC 3036, January 2001. [RFC 3037] Thomas, B. and E. Gray, "LDP Applicability", RFC 3037, January 2001. [RFC 3215] Boscher, C., Cheval, P., Wu, L., and E. Gray, "LDP State Machine", RFC 3215, January 2002. [RFC 3289] Baker, F., Chan, K., and A. Smith, "Management Information Base for the Differentiated Services Architecture", RFC 3289, May 2002. [RFC 3291] Daniele, M., Haberman, B., Routhier, S., and J. Schoenwaelder, "Textual Coventions for Internet Network Addresses", RFC 3291, May 2002. [RFC 3413] Levi, D., Meyers, P. and B. Stewart, "Simple Network Management Protocol (SNMP) Applications", STD 62, RFC 3413, December 2002. Cucchiara, et al. Standards Track PAGE 99

RFC 3815 MPLS LDP MIB June 2004 [RFC 3811] Nadeau, T. and J. Cucchiara, Editors "Definitions of Textual Conventions (TCs) for Multiprotocol Label Switching (MPLS) Management", RFC 3811, June 2004. [RFC 3813] Srinivansan, C., Viswanathan, A., and T. Nadeau, "Multiprotocol Label Switching (MPLS) Label Switching Router (LSR) Management Information Base (MIB)", RFC 3813, June 2004 6.2. Informative References [MPLSMGMT] Nadeau, T., Srinivasan, C., and A. Farrel, "Multiprotocol Label Switching (MPLS) Management Overview", Work in Progress, September 2003. [RFC 2684] Grossman, D. and J. Heinanen, "Multiprotocol Encapsulation over ATM Adaptation Layer 5", RFC 2684, September 1999. [RFC 3410] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002. 7. Security Considerations This Security Considerations section consists of 4 subsections, one for each of the MIB Modules in this document. 7.1. Security Considerations for MPLS-LDP-STD-MIB There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: o the mplsLdpEntityTable contains objects to provision potential LDP sessions on the Label Switching Router (LSR) or Label Edge Router (LER). The mplsLdpLspFecTable contains objects which associate an LSP with a FEC. Unauthorized access to objects in these tables, could result in disruption of traffic on the network. This is especially true if an LDP session has been established. The use of stronger mechanisms such as SNMPv3 security should be considered where possible. Specifically, SNMPv3 VACM and USM MUST be used with any v3 agent which implements this MIB. Administrators should consider whether Cucchiara, et al. Standards Track PAGE 100

RFC 3815 MPLS LDP MIB June 2004 read access to these objects should be allowed, since read access may be undesirable under certain circumstances. Some of the readable objects in this MIB module i.e., (objects with a MAX-ACCESS other than not-accessible), may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: o the mplsLdpEntityTable, mplsLdpPeerTable, mplsLdpSessionTable and mplsLdpSessionStatsTable collectively show the LDP LSP network topology. If an Administrator does not want to reveal the LDP LSP topology of the network, then these tables should be considered sensitive/vulnerable. 7.2. Security Considerations for MPLS-LDP-ATM-STD-MIB There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: o the mplsLdpEntityAtmTable and mplsLdpEntityAtmLRTable contain objects to provision potential LDP sessions on the Label Switching Router (LSR) or Label Edge Router (LER) over Layer 2 of ATM. These tables extend the mplsLdpEntityTable in the MPLS- LDP-MIB. Unauthorized access to objects in these tables, could result in disruption of traffic on the network. This is especially true if an LDP session has been established. The use of stronger mechanisms such as SNMPv3 security should be considered where possible. Specifically, SNMPv3 VACM and USM MUST be used with any v3 agent which implements this MIB. Administrators should consider whether read access to these objects should be allowed, since read access may be undesirable under certain circumstances. Some of the readable objects in this MIB module i.e., (objects with a MAX-ACCESS other than not-accessible), may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: Cucchiara, et al. Standards Track PAGE 101

RFC 3815 MPLS LDP MIB June 2004 o the mplsLdpEntityAtmTable and mplsLdpEntityAtmLRTable show the Label Ranges for ATM. If an Administrator does not want to reveal this information then these tables should be considered sensitive/vulnerable and treated accordingly. 7.3. Security Considerations for MPLS-LDP-FRAME-RELAY-STD-MIB There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: o the mplsLdpEntityFrameRelayTable and mplsLdpEntityFrameRelayLRTable contain objects to provision potential LDP sessions on the Label Switching Router (LSR) or Label Edge Router (LER) over Layer 2 of Frame Relay. These tables extend the mplsLdpEntityTable in the MPLS-LDP-MIB. Unauthorized access to objects in these tables, could result in disruption of traffic on the network. This is especially true if an LDP session has been established. The use of stronger mechanisms such as SNMPv3 security should be considered where possible. Specifically, SNMPv3 VACM and USM MUST be used with any v3 agent which implements this MIB. Administrators should consider whether read access to these objects should be allowed, since read access may be undesirable under certain circumstances. Some of the readable objects in this MIB module i.e., (objects with a MAX-ACCESS other than not-accessible), may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: o the mplsLdpEntityFrameRelayTable and mplsLdpEntityFrameRelayLRTable show the Label Ranges for Frame Relay. If an Administrator does not want to reveal this information then these tables should be considered sensitive/vulnerable and treated accordingly. Cucchiara, et al. Standards Track PAGE 102

RFC 3815 MPLS LDP MIB June 2004 7.4. Security Considerations for MPLS-LDP-GENERIC-STD-MIB There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: o the mplsLdpEntityGenericLRTable contains objects to provision potential LDP sessions on the Label Switching Router (LSR) or Label Edge Router (LER) over Layer 2 of Ethernet. This table extends the mplsLdpEntityTable in the MPLS-LDP-MIB. Unauthorized access to objects in these tables, could result in disruption of traffic on the network. This is especially true if an LDP session has been established. The use of stronger mechanisms such as SNMPv3 security should be considered where possible. Specifically, SNMPv3 VACM and USM MUST be used with any v3 agent which implements this MIB. Administrators should consider whether read access to these objects should be allowed, since read access may be undesirable under certain circumstances. Some of the readable objects in this MIB module i.e., (objects with a MAX-ACCESS other than not-accessible), may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: o the mplsLdpEntityGenericLRTable shows the Label Ranges for ethernet. If an Administrator does not want to reveal this information then these tables should be considered sensitive/vulnerable and treated accordingly. 7.5. Additional Security Considerations The following paragraphs describe additional security considerations which are applicable to all 4 of the MIB Modules in this document. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. Cucchiara, et al. Standards Track PAGE 103

RFC 3815 MPLS LDP MIB June 2004 It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC 3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module, is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 8. IANA Considerations As described in [MPLSMGMT] and as requested in the MPLS-TC-STD-MIB [MPLSTCMIB], MPLS related standards track MIB modules should be rooted under the mplsStdMIB subtree. There are 4 MPLS MIB Modules contained in this document, each of the following "IANA Considerations" subsections lists new IANA assignments under the mplsStdMIB subtree. New assignments can only be made via a Standards Action as specified in [RFC 2434]. 8.1. IANA Considerations for MPLS-LDP-STD-MIB The IANA has assigned { mplsStdMIB 4 } to the MPLS-LDP-STD-MIB module specified in this document. 8.2. IANA Considerations for MPLS-LDP-ATM-STD-MIB The IANA has assigned { mplsStdMIB 5 } to the MPLS-LDP-ATM-STD-MIB module specified in this document. 8.3. IANA Considerations for MPLS-LDP-FRAME-RELAY-STD-MIB The IANA has assigned { mplsStdMIB 6 } to the MPLS-LDP-FRAME-RELAY- STD-MIB module specified in this document. 8.4. IANA Considerations for MPLS-LDP-GENERIC-STD-MIB The IANA has assigned { mplsStdMIB 7 } to the MPLS-LDP-GENERIC-STD- MIB module specified in this document. Cucchiara, et al. Standards Track PAGE 104

RFC 3815 MPLS LDP MIB June 2004 9. Authors' Addresses James V. Luciani Marconi Communications, Inc. 900 Chelmsford Street Lowell, MA 01851 EMail: james_luciani@mindspring.com Hans Sjostrand ipUnplugged P.O. Box 101 60 S-121 28 Stockholm, Sweden Phone: +46 8 725 5900 EMail: hans@ipunplugged.com Joan E. Cucchiara Marconi Communications, Inc. 900 Chelmsford Street Lowell, MA 01851 Phone: +1 978 275 7400 EMail: jcucchiara@mindspring.com Cucchiara, et al. Standards Track PAGE 105

RFC 3815 MPLS LDP MIB June 2004 10. Full Copyright Statement Copyright © The Internet Society (2004). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society. Cucchiara, et al. Standards Track PAGE 106

Definitions of Managed Objects for the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP) RFC TOTAL SIZE: 215916 bytes PUBLICATION DATE: Thursday, June 17th, 2004 LEGAL RIGHTS: The IETF Trust (see BCP 78)


RFC-ARCHIVE.ORG

© RFC 3815: The IETF Trust, Thursday, June 17th, 2004
© the RFC Archive, 2024, RFC-Archive.org
Maintainer: J. Tunnissen

Privacy Statement